shell bypass 403
UnknownSec Shell
:
/
usr
/
src
/
linux-headers-6.8.0-83-generic
/
arch
/
powerpc
/
include
/
asm
/ [
drwxr-xr-x
]
upload
mass deface
mass delete
console
info server
name :
cpm2.h
/* SPDX-License-Identifier: GPL-2.0 */ /* * Communication Processor Module v2. * * This file contains structures and information for the communication * processor channels found in the dual port RAM or parameter RAM. * All CPM control and status is available through the CPM2 internal * memory map. See immap_cpm2.h for details. */ #ifdef __KERNEL__ #ifndef __CPM2__ #define __CPM2__ #include <asm/immap_cpm2.h> #include <asm/cpm.h> #include <sysdev/fsl_soc.h> /* CPM Command register. */ #define CPM_CR_RST ((uint)0x80000000) #define CPM_CR_PAGE ((uint)0x7c000000) #define CPM_CR_SBLOCK ((uint)0x03e00000) #define CPM_CR_FLG ((uint)0x00010000) #define CPM_CR_MCN ((uint)0x00003fc0) #define CPM_CR_OPCODE ((uint)0x0000000f) /* Device sub-block and page codes. */ #define CPM_CR_SCC1_SBLOCK (0x04) #define CPM_CR_SCC2_SBLOCK (0x05) #define CPM_CR_SCC3_SBLOCK (0x06) #define CPM_CR_SCC4_SBLOCK (0x07) #define CPM_CR_SMC1_SBLOCK (0x08) #define CPM_CR_SMC2_SBLOCK (0x09) #define CPM_CR_SPI_SBLOCK (0x0a) #define CPM_CR_I2C_SBLOCK (0x0b) #define CPM_CR_TIMER_SBLOCK (0x0f) #define CPM_CR_RAND_SBLOCK (0x0e) #define CPM_CR_FCC1_SBLOCK (0x10) #define CPM_CR_FCC2_SBLOCK (0x11) #define CPM_CR_FCC3_SBLOCK (0x12) #define CPM_CR_IDMA1_SBLOCK (0x14) #define CPM_CR_IDMA2_SBLOCK (0x15) #define CPM_CR_IDMA3_SBLOCK (0x16) #define CPM_CR_IDMA4_SBLOCK (0x17) #define CPM_CR_MCC1_SBLOCK (0x1c) #define CPM_CR_FCC_SBLOCK(x) (x + 0x10) #define CPM_CR_SCC1_PAGE (0x00) #define CPM_CR_SCC2_PAGE (0x01) #define CPM_CR_SCC3_PAGE (0x02) #define CPM_CR_SCC4_PAGE (0x03) #define CPM_CR_SMC1_PAGE (0x07) #define CPM_CR_SMC2_PAGE (0x08) #define CPM_CR_SPI_PAGE (0x09) #define CPM_CR_I2C_PAGE (0x0a) #define CPM_CR_TIMER_PAGE (0x0a) #define CPM_CR_RAND_PAGE (0x0a) #define CPM_CR_FCC1_PAGE (0x04) #define CPM_CR_FCC2_PAGE (0x05) #define CPM_CR_FCC3_PAGE (0x06) #define CPM_CR_IDMA1_PAGE (0x07) #define CPM_CR_IDMA2_PAGE (0x08) #define CPM_CR_IDMA3_PAGE (0x09) #define CPM_CR_IDMA4_PAGE (0x0a) #define CPM_CR_MCC1_PAGE (0x07) #define CPM_CR_MCC2_PAGE (0x08) #define CPM_CR_FCC_PAGE(x) (x + 0x04) /* CPM2-specific opcodes (see cpm.h for common opcodes) */ #define CPM_CR_START_IDMA ((ushort)0x0009) #define mk_cr_cmd(PG, SBC, MCN, OP) \ ((PG << 26) | (SBC << 21) | (MCN << 6) | OP) /* The number of pages of host memory we allocate for CPM. This is * done early in kernel initialization to get physically contiguous * pages. */ #define NUM_CPM_HOST_PAGES 2 /* Export the base address of the communication processor registers * and dual port ram. */ extern cpm_cpm2_t __iomem *cpmp; /* Pointer to comm processor */ extern void cpm2_reset(void); /* Baud rate generators. */ #define CPM_BRG_RST ((uint)0x00020000) #define CPM_BRG_EN ((uint)0x00010000) #define CPM_BRG_EXTC_INT ((uint)0x00000000) #define CPM_BRG_EXTC_CLK3_9 ((uint)0x00004000) #define CPM_BRG_EXTC_CLK5_15 ((uint)0x00008000) #define CPM_BRG_ATB ((uint)0x00002000) #define CPM_BRG_CD_MASK ((uint)0x00001ffe) #define CPM_BRG_DIV16 ((uint)0x00000001) #define CPM2_BRG_INT_CLK (get_brgfreq()) #define CPM2_BRG_UART_CLK (CPM2_BRG_INT_CLK/16) extern void __cpm2_setbrg(uint brg, uint rate, uint clk, int div16, int src); /* This function is used by UARTS, or anything else that uses a 16x * oversampled clock. */ static inline void cpm_setbrg(uint brg, uint rate) { __cpm2_setbrg(brg, rate, CPM2_BRG_UART_CLK, 0, CPM_BRG_EXTC_INT); } /* This function is used to set high speed synchronous baud rate * clocks. */ static inline void cpm2_fastbrg(uint brg, uint rate, int div16) { __cpm2_setbrg(brg, rate, CPM2_BRG_INT_CLK, div16, CPM_BRG_EXTC_INT); } /* Parameter RAM offsets from the base. */ #define PROFF_SCC1 ((uint)0x8000) #define PROFF_SCC2 ((uint)0x8100) #define PROFF_SCC3 ((uint)0x8200) #define PROFF_SCC4 ((uint)0x8300) #define PROFF_FCC1 ((uint)0x8400) #define PROFF_FCC2 ((uint)0x8500) #define PROFF_FCC3 ((uint)0x8600) #define PROFF_MCC1 ((uint)0x8700) #define PROFF_SMC1_BASE ((uint)0x87fc) #define PROFF_IDMA1_BASE ((uint)0x87fe) #define PROFF_MCC2 ((uint)0x8800) #define PROFF_SMC2_BASE ((uint)0x88fc) #define PROFF_IDMA2_BASE ((uint)0x88fe) #define PROFF_SPI_BASE ((uint)0x89fc) #define PROFF_IDMA3_BASE ((uint)0x89fe) #define PROFF_TIMERS ((uint)0x8ae0) #define PROFF_REVNUM ((uint)0x8af0) #define PROFF_RAND ((uint)0x8af8) #define PROFF_I2C_BASE ((uint)0x8afc) #define PROFF_IDMA4_BASE ((uint)0x8afe) #define PROFF_SCC_SIZE ((uint)0x100) #define PROFF_FCC_SIZE ((uint)0x100) #define PROFF_SMC_SIZE ((uint)64) /* The SMCs are relocated to any of the first eight DPRAM pages. * We will fix these at the first locations of DPRAM, until we * get some microcode patches :-). * The parameter ram space for the SMCs is fifty-some bytes, and * they are required to start on a 64 byte boundary. */ #define PROFF_SMC1 (0) #define PROFF_SMC2 (64) /* Define enough so I can at least use the serial port as a UART. */ typedef struct smc_uart { ushort smc_rbase; /* Rx Buffer descriptor base address */ ushort smc_tbase; /* Tx Buffer descriptor base address */ u_char smc_rfcr; /* Rx function code */ u_char smc_tfcr; /* Tx function code */ ushort smc_mrblr; /* Max receive buffer length */ uint smc_rstate; /* Internal */ uint smc_idp; /* Internal */ ushort smc_rbptr; /* Internal */ ushort smc_ibc; /* Internal */ uint smc_rxtmp; /* Internal */ uint smc_tstate; /* Internal */ uint smc_tdp; /* Internal */ ushort smc_tbptr; /* Internal */ ushort smc_tbc; /* Internal */ uint smc_txtmp; /* Internal */ ushort smc_maxidl; /* Maximum idle characters */ ushort smc_tmpidl; /* Temporary idle counter */ ushort smc_brklen; /* Last received break length */ ushort smc_brkec; /* rcv'd break condition counter */ ushort smc_brkcr; /* xmt break count register */ ushort smc_rmask; /* Temporary bit mask */ uint smc_stmp; /* SDMA Temp */ } smc_uart_t; /* SMC uart mode register (Internal memory map). */ #define SMCMR_REN ((ushort)0x0001) #define SMCMR_TEN ((ushort)0x0002) #define SMCMR_DM ((ushort)0x000c) #define SMCMR_SM_GCI ((ushort)0x0000) #define SMCMR_SM_UART ((ushort)0x0020) #define SMCMR_SM_TRANS ((ushort)0x0030) #define SMCMR_SM_MASK ((ushort)0x0030) #define SMCMR_PM_EVEN ((ushort)0x0100) /* Even parity, else odd */ #define SMCMR_REVD SMCMR_PM_EVEN #define SMCMR_PEN ((ushort)0x0200) /* Parity enable */ #define SMCMR_BS SMCMR_PEN #define SMCMR_SL ((ushort)0x0400) /* Two stops, else one */ #define SMCR_CLEN_MASK ((ushort)0x7800) /* Character length */ #define smcr_mk_clen(C) (((C) << 11) & SMCR_CLEN_MASK) /* SMC Event and Mask register. */ #define SMCM_BRKE ((unsigned char)0x40) /* When in UART Mode */ #define SMCM_BRK ((unsigned char)0x10) /* When in UART Mode */ #define SMCM_TXE ((unsigned char)0x10) #define SMCM_BSY ((unsigned char)0x04) #define SMCM_TX ((unsigned char)0x02) #define SMCM_RX ((unsigned char)0x01) /* SCCs. */ #define SCC_GSMRH_IRP ((uint)0x00040000) #define SCC_GSMRH_GDE ((uint)0x00010000) #define SCC_GSMRH_TCRC_CCITT ((uint)0x00008000) #define SCC_GSMRH_TCRC_BISYNC ((uint)0x00004000) #define SCC_GSMRH_TCRC_HDLC ((uint)0x00000000) #define SCC_GSMRH_REVD ((uint)0x00002000) #define SCC_GSMRH_TRX ((uint)0x00001000) #define SCC_GSMRH_TTX ((uint)0x00000800) #define SCC_GSMRH_CDP ((uint)0x00000400) #define SCC_GSMRH_CTSP ((uint)0x00000200) #define SCC_GSMRH_CDS ((uint)0x00000100) #define SCC_GSMRH_CTSS ((uint)0x00000080) #define SCC_GSMRH_TFL ((uint)0x00000040) #define SCC_GSMRH_RFW ((uint)0x00000020) #define SCC_GSMRH_TXSY ((uint)0x00000010) #define SCC_GSMRH_SYNL16 ((uint)0x0000000c) #define SCC_GSMRH_SYNL8 ((uint)0x00000008) #define SCC_GSMRH_SYNL4 ((uint)0x00000004) #define SCC_GSMRH_RTSM ((uint)0x00000002) #define SCC_GSMRH_RSYN ((uint)0x00000001) #define SCC_GSMRL_SIR ((uint)0x80000000) /* SCC2 only */ #define SCC_GSMRL_EDGE_NONE ((uint)0x60000000) #define SCC_GSMRL_EDGE_NEG ((uint)0x40000000) #define SCC_GSMRL_EDGE_POS ((uint)0x20000000) #define SCC_GSMRL_EDGE_BOTH ((uint)0x00000000) #define SCC_GSMRL_TCI ((uint)0x10000000) #define SCC_GSMRL_TSNC_3 ((uint)0x0c000000) #define SCC_GSMRL_TSNC_4 ((uint)0x08000000) #define SCC_GSMRL_TSNC_14 ((uint)0x04000000) #define SCC_GSMRL_TSNC_INF ((uint)0x00000000) #define SCC_GSMRL_RINV ((uint)0x02000000) #define SCC_GSMRL_TINV ((uint)0x01000000) #define SCC_GSMRL_TPL_128 ((uint)0x00c00000) #define SCC_GSMRL_TPL_64 ((uint)0x00a00000) #define SCC_GSMRL_TPL_48 ((uint)0x00800000) #define SCC_GSMRL_TPL_32 ((uint)0x00600000) #define SCC_GSMRL_TPL_16 ((uint)0x00400000) #define SCC_GSMRL_TPL_8 ((uint)0x00200000) #define SCC_GSMRL_TPL_NONE ((uint)0x00000000) #define SCC_GSMRL_TPP_ALL1 ((uint)0x00180000) #define SCC_GSMRL_TPP_01 ((uint)0x00100000) #define SCC_GSMRL_TPP_10 ((uint)0x00080000) #define SCC_GSMRL_TPP_ZEROS ((uint)0x00000000) #define SCC_GSMRL_TEND ((uint)0x00040000) #define SCC_GSMRL_TDCR_32 ((uint)0x00030000) #define SCC_GSMRL_TDCR_16 ((uint)0x00020000) #define SCC_GSMRL_TDCR_8 ((uint)0x00010000) #define SCC_GSMRL_TDCR_1 ((uint)0x00000000) #define SCC_GSMRL_RDCR_32 ((uint)0x0000c000) #define SCC_GSMRL_RDCR_16 ((uint)0x00008000) #define SCC_GSMRL_RDCR_8 ((uint)0x00004000) #define SCC_GSMRL_RDCR_1 ((uint)0x00000000) #define SCC_GSMRL_RENC_DFMAN ((uint)0x00003000) #define SCC_GSMRL_RENC_MANCH ((uint)0x00002000) #define SCC_GSMRL_RENC_FM0 ((uint)0x00001000) #define SCC_GSMRL_RENC_NRZI ((uint)0x00000800) #define SCC_GSMRL_RENC_NRZ ((uint)0x00000000) #define SCC_GSMRL_TENC_DFMAN ((uint)0x00000600) #define SCC_GSMRL_TENC_MANCH ((uint)0x00000400) #define SCC_GSMRL_TENC_FM0 ((uint)0x00000200) #define SCC_GSMRL_TENC_NRZI ((uint)0x00000100) #define SCC_GSMRL_TENC_NRZ ((uint)0x00000000) #define SCC_GSMRL_DIAG_LE ((uint)0x000000c0) /* Loop and echo */ #define SCC_GSMRL_DIAG_ECHO ((uint)0x00000080) #define SCC_GSMRL_DIAG_LOOP ((uint)0x00000040) #define SCC_GSMRL_DIAG_NORM ((uint)0x00000000) #define SCC_GSMRL_ENR ((uint)0x00000020) #define SCC_GSMRL_ENT ((uint)0x00000010) #define SCC_GSMRL_MODE_ENET ((uint)0x0000000c) #define SCC_GSMRL_MODE_DDCMP ((uint)0x00000009) #define SCC_GSMRL_MODE_BISYNC ((uint)0x00000008) #define SCC_GSMRL_MODE_V14 ((uint)0x00000007) #define SCC_GSMRL_MODE_AHDLC ((uint)0x00000006) #define SCC_GSMRL_MODE_PROFIBUS ((uint)0x00000005) #define SCC_GSMRL_MODE_UART ((uint)0x00000004) #define SCC_GSMRL_MODE_SS7 ((uint)0x00000003) #define SCC_GSMRL_MODE_ATALK ((uint)0x00000002) #define SCC_GSMRL_MODE_HDLC ((uint)0x00000000) #define SCC_TODR_TOD ((ushort)0x8000) /* SCC Event and Mask register. */ #define SCCM_TXE ((unsigned char)0x10) #define SCCM_BSY ((unsigned char)0x04) #define SCCM_TX ((unsigned char)0x02) #define SCCM_RX ((unsigned char)0x01) typedef struct scc_param { ushort scc_rbase; /* Rx Buffer descriptor base address */ ushort scc_tbase; /* Tx Buffer descriptor base address */ u_char scc_rfcr; /* Rx function code */ u_char scc_tfcr; /* Tx function code */ ushort scc_mrblr; /* Max receive buffer length */ uint scc_rstate; /* Internal */ uint scc_idp; /* Internal */ ushort scc_rbptr; /* Internal */ ushort scc_ibc; /* Internal */ uint scc_rxtmp; /* Internal */ uint scc_tstate; /* Internal */ uint scc_tdp; /* Internal */ ushort scc_tbptr; /* Internal */ ushort scc_tbc; /* Internal */ uint scc_txtmp; /* Internal */ uint scc_rcrc; /* Internal */ uint scc_tcrc; /* Internal */ } sccp_t; /* Function code bits. */ #define SCC_EB ((u_char) 0x10) /* Set big endian byte order */ #define SCC_GBL ((u_char) 0x20) /* Snooping enabled */ /* CPM Ethernet through SCC1. */ typedef struct scc_enet { sccp_t sen_genscc; uint sen_cpres; /* Preset CRC */ uint sen_cmask; /* Constant mask for CRC */ uint sen_crcec; /* CRC Error counter */ uint sen_alec; /* alignment error counter */ uint sen_disfc; /* discard frame counter */ ushort sen_pads; /* Tx short frame pad character */ ushort sen_retlim; /* Retry limit threshold */ ushort sen_retcnt; /* Retry limit counter */ ushort sen_maxflr; /* maximum frame length register */ ushort sen_minflr; /* minimum frame length register */ ushort sen_maxd1; /* maximum DMA1 length */ ushort sen_maxd2; /* maximum DMA2 length */ ushort sen_maxd; /* Rx max DMA */ ushort sen_dmacnt; /* Rx DMA counter */ ushort sen_maxb; /* Max BD byte count */ ushort sen_gaddr1; /* Group address filter */ ushort sen_gaddr2; ushort sen_gaddr3; ushort sen_gaddr4; uint sen_tbuf0data0; /* Save area 0 - current frame */ uint sen_tbuf0data1; /* Save area 1 - current frame */ uint sen_tbuf0rba; /* Internal */ uint sen_tbuf0crc; /* Internal */ ushort sen_tbuf0bcnt; /* Internal */ ushort sen_paddrh; /* physical address (MSB) */ ushort sen_paddrm; ushort sen_paddrl; /* physical address (LSB) */ ushort sen_pper; /* persistence */ ushort sen_rfbdptr; /* Rx first BD pointer */ ushort sen_tfbdptr; /* Tx first BD pointer */ ushort sen_tlbdptr; /* Tx last BD pointer */ uint sen_tbuf1data0; /* Save area 0 - current frame */ uint sen_tbuf1data1; /* Save area 1 - current frame */ uint sen_tbuf1rba; /* Internal */ uint sen_tbuf1crc; /* Internal */ ushort sen_tbuf1bcnt; /* Internal */ ushort sen_txlen; /* Tx Frame length counter */ ushort sen_iaddr1; /* Individual address filter */ ushort sen_iaddr2; ushort sen_iaddr3; ushort sen_iaddr4; ushort sen_boffcnt; /* Backoff counter */ /* NOTE: Some versions of the manual have the following items * incorrectly documented. Below is the proper order. */ ushort sen_taddrh; /* temp address (MSB) */ ushort sen_taddrm; ushort sen_taddrl; /* temp address (LSB) */ } scc_enet_t; /* SCC Event register as used by Ethernet. */ #define SCCE_ENET_GRA ((ushort)0x0080) /* Graceful stop complete */ #define SCCE_ENET_TXE ((ushort)0x0010) /* Transmit Error */ #define SCCE_ENET_RXF ((ushort)0x0008) /* Full frame received */ #define SCCE_ENET_BSY ((ushort)0x0004) /* All incoming buffers full */ #define SCCE_ENET_TXB ((ushort)0x0002) /* A buffer was transmitted */ #define SCCE_ENET_RXB ((ushort)0x0001) /* A buffer was received */ /* SCC Mode Register (PSMR) as used by Ethernet. */ #define SCC_PSMR_HBC ((ushort)0x8000) /* Enable heartbeat */ #define SCC_PSMR_FC ((ushort)0x4000) /* Force collision */ #define SCC_PSMR_RSH ((ushort)0x2000) /* Receive short frames */ #define SCC_PSMR_IAM ((ushort)0x1000) /* Check individual hash */ #define SCC_PSMR_ENCRC ((ushort)0x0800) /* Ethernet CRC mode */ #define SCC_PSMR_PRO ((ushort)0x0200) /* Promiscuous mode */ #define SCC_PSMR_BRO ((ushort)0x0100) /* Catch broadcast pkts */ #define SCC_PSMR_SBT ((ushort)0x0080) /* Special backoff timer */ #define SCC_PSMR_LPB ((ushort)0x0040) /* Set Loopback mode */ #define SCC_PSMR_SIP ((ushort)0x0020) /* Sample Input Pins */ #define SCC_PSMR_LCW ((ushort)0x0010) /* Late collision window */ #define SCC_PSMR_NIB22 ((ushort)0x000a) /* Start frame search */ #define SCC_PSMR_FDE ((ushort)0x0001) /* Full duplex enable */ /* SCC as UART */ typedef struct scc_uart { sccp_t scc_genscc; uint scc_res1; /* Reserved */ uint scc_res2; /* Reserved */ ushort scc_maxidl; /* Maximum idle chars */ ushort scc_idlc; /* temp idle counter */ ushort scc_brkcr; /* Break count register */ ushort scc_parec; /* receive parity error counter */ ushort scc_frmec; /* receive framing error counter */ ushort scc_nosec; /* receive noise counter */ ushort scc_brkec; /* receive break condition counter */ ushort scc_brkln; /* last received break length */ ushort scc_uaddr1; /* UART address character 1 */ ushort scc_uaddr2; /* UART address character 2 */ ushort scc_rtemp; /* Temp storage */ ushort scc_toseq; /* Transmit out of sequence char */ ushort scc_char1; /* control character 1 */ ushort scc_char2; /* control character 2 */ ushort scc_char3; /* control character 3 */ ushort scc_char4; /* control character 4 */ ushort scc_char5; /* control character 5 */ ushort scc_char6; /* control character 6 */ ushort scc_char7; /* control character 7 */ ushort scc_char8; /* control character 8 */ ushort scc_rccm; /* receive control character mask */ ushort scc_rccr; /* receive control character register */ ushort scc_rlbc; /* receive last break character */ } scc_uart_t; /* SCC Event and Mask registers when it is used as a UART. */ #define UART_SCCM_GLR ((ushort)0x1000) #define UART_SCCM_GLT ((ushort)0x0800) #define UART_SCCM_AB ((ushort)0x0200) #define UART_SCCM_IDL ((ushort)0x0100) #define UART_SCCM_GRA ((ushort)0x0080) #define UART_SCCM_BRKE ((ushort)0x0040) #define UART_SCCM_BRKS ((ushort)0x0020) #define UART_SCCM_CCR ((ushort)0x0008) #define UART_SCCM_BSY ((ushort)0x0004) #define UART_SCCM_TX ((ushort)0x0002) #define UART_SCCM_RX ((ushort)0x0001) /* The SCC PSMR when used as a UART. */ #define SCU_PSMR_FLC ((ushort)0x8000) #define SCU_PSMR_SL ((ushort)0x4000) #define SCU_PSMR_CL ((ushort)0x3000) #define SCU_PSMR_UM ((ushort)0x0c00) #define SCU_PSMR_FRZ ((ushort)0x0200) #define SCU_PSMR_RZS ((ushort)0x0100) #define SCU_PSMR_SYN ((ushort)0x0080) #define SCU_PSMR_DRT ((ushort)0x0040) #define SCU_PSMR_PEN ((ushort)0x0010) #define SCU_PSMR_RPM ((ushort)0x000c) #define SCU_PSMR_REVP ((ushort)0x0008) #define SCU_PSMR_TPM ((ushort)0x0003) #define SCU_PSMR_TEVP ((ushort)0x0002) /* CPM Transparent mode SCC. */ typedef struct scc_trans { sccp_t st_genscc; uint st_cpres; /* Preset CRC */ uint st_cmask; /* Constant mask for CRC */ } scc_trans_t; /* How about some FCCs..... */ #define FCC_GFMR_DIAG_NORM ((uint)0x00000000) #define FCC_GFMR_DIAG_LE ((uint)0x40000000) #define FCC_GFMR_DIAG_AE ((uint)0x80000000) #define FCC_GFMR_DIAG_ALE ((uint)0xc0000000) #define FCC_GFMR_TCI ((uint)0x20000000) #define FCC_GFMR_TRX ((uint)0x10000000) #define FCC_GFMR_TTX ((uint)0x08000000) #define FCC_GFMR_CDP ((uint)0x04000000) #define FCC_GFMR_CTSP ((uint)0x02000000) #define FCC_GFMR_CDS ((uint)0x01000000) #define FCC_GFMR_CTSS ((uint)0x00800000) #define FCC_GFMR_SYNL_NONE ((uint)0x00000000) #define FCC_GFMR_SYNL_AUTO ((uint)0x00004000) #define FCC_GFMR_SYNL_8 ((uint)0x00008000) #define FCC_GFMR_SYNL_16 ((uint)0x0000c000) #define FCC_GFMR_RTSM ((uint)0x00002000) #define FCC_GFMR_RENC_NRZ ((uint)0x00000000) #define FCC_GFMR_RENC_NRZI ((uint)0x00000800) #define FCC_GFMR_REVD ((uint)0x00000400) #define FCC_GFMR_TENC_NRZ ((uint)0x00000000) #define FCC_GFMR_TENC_NRZI ((uint)0x00000100) #define FCC_GFMR_TCRC_16 ((uint)0x00000000) #define FCC_GFMR_TCRC_32 ((uint)0x00000080) #define FCC_GFMR_ENR ((uint)0x00000020) #define FCC_GFMR_ENT ((uint)0x00000010) #define FCC_GFMR_MODE_ENET ((uint)0x0000000c) #define FCC_GFMR_MODE_ATM ((uint)0x0000000a) #define FCC_GFMR_MODE_HDLC ((uint)0x00000000) /* Generic FCC parameter ram. */ typedef struct fcc_param { ushort fcc_riptr; /* Rx Internal temp pointer */ ushort fcc_tiptr; /* Tx Internal temp pointer */ ushort fcc_res1; ushort fcc_mrblr; /* Max receive buffer length, mod 32 bytes */ uint fcc_rstate; /* Upper byte is Func code, must be set */ uint fcc_rbase; /* Receive BD base */ ushort fcc_rbdstat; /* RxBD status */ ushort fcc_rbdlen; /* RxBD down counter */ uint fcc_rdptr; /* RxBD internal data pointer */ uint fcc_tstate; /* Upper byte is Func code, must be set */ uint fcc_tbase; /* Transmit BD base */ ushort fcc_tbdstat; /* TxBD status */ ushort fcc_tbdlen; /* TxBD down counter */ uint fcc_tdptr; /* TxBD internal data pointer */ uint fcc_rbptr; /* Rx BD Internal buf pointer */ uint fcc_tbptr; /* Tx BD Internal buf pointer */ uint fcc_rcrc; /* Rx temp CRC */ uint fcc_res2; uint fcc_tcrc; /* Tx temp CRC */ } fccp_t; /* Ethernet controller through FCC. */ typedef struct fcc_enet { fccp_t fen_genfcc; uint fen_statbuf; /* Internal status buffer */ uint fen_camptr; /* CAM address */ uint fen_cmask; /* Constant mask for CRC */ uint fen_cpres; /* Preset CRC */ uint fen_crcec; /* CRC Error counter */ uint fen_alec; /* alignment error counter */ uint fen_disfc; /* discard frame counter */ ushort fen_retlim; /* Retry limit */ ushort fen_retcnt; /* Retry counter */ ushort fen_pper; /* Persistence */ ushort fen_boffcnt; /* backoff counter */ uint fen_gaddrh; /* Group address filter, high 32-bits */ uint fen_gaddrl; /* Group address filter, low 32-bits */ ushort fen_tfcstat; /* out of sequence TxBD */ ushort fen_tfclen; uint fen_tfcptr; ushort fen_mflr; /* Maximum frame length (1518) */ ushort fen_paddrh; /* MAC address */ ushort fen_paddrm; ushort fen_paddrl; ushort fen_ibdcount; /* Internal BD counter */ ushort fen_ibdstart; /* Internal BD start pointer */ ushort fen_ibdend; /* Internal BD end pointer */ ushort fen_txlen; /* Internal Tx frame length counter */ uint fen_ibdbase[8]; /* Internal use */ uint fen_iaddrh; /* Individual address filter */ uint fen_iaddrl; ushort fen_minflr; /* Minimum frame length (64) */ ushort fen_taddrh; /* Filter transfer MAC address */ ushort fen_taddrm; ushort fen_taddrl; ushort fen_padptr; /* Pointer to pad byte buffer */ ushort fen_cftype; /* control frame type */ ushort fen_cfrange; /* control frame range */ ushort fen_maxb; /* maximum BD count */ ushort fen_maxd1; /* Max DMA1 length (1520) */ ushort fen_maxd2; /* Max DMA2 length (1520) */ ushort fen_maxd; /* internal max DMA count */ ushort fen_dmacnt; /* internal DMA counter */ uint fen_octc; /* Total octect counter */ uint fen_colc; /* Total collision counter */ uint fen_broc; /* Total broadcast packet counter */ uint fen_mulc; /* Total multicast packet count */ uint fen_uspc; /* Total packets < 64 bytes */ uint fen_frgc; /* Total packets < 64 bytes with errors */ uint fen_ospc; /* Total packets > 1518 */ uint fen_jbrc; /* Total packets > 1518 with errors */ uint fen_p64c; /* Total packets == 64 bytes */ uint fen_p65c; /* Total packets 64 < bytes <= 127 */ uint fen_p128c; /* Total packets 127 < bytes <= 255 */ uint fen_p256c; /* Total packets 256 < bytes <= 511 */ uint fen_p512c; /* Total packets 512 < bytes <= 1023 */ uint fen_p1024c; /* Total packets 1024 < bytes <= 1518 */ uint fen_cambuf; /* Internal CAM buffer pointer */ ushort fen_rfthr; /* Received frames threshold */ ushort fen_rfcnt; /* Received frames count */ } fcc_enet_t; /* FCC Event/Mask register as used by Ethernet. */ #define FCC_ENET_GRA ((ushort)0x0080) /* Graceful stop complete */ #define FCC_ENET_RXC ((ushort)0x0040) /* Control Frame Received */ #define FCC_ENET_TXC ((ushort)0x0020) /* Out of seq. Tx sent */ #define FCC_ENET_TXE ((ushort)0x0010) /* Transmit Error */ #define FCC_ENET_RXF ((ushort)0x0008) /* Full frame received */ #define FCC_ENET_BSY ((ushort)0x0004) /* Busy. Rx Frame dropped */ #define FCC_ENET_TXB ((ushort)0x0002) /* A buffer was transmitted */ #define FCC_ENET_RXB ((ushort)0x0001) /* A buffer was received */ /* FCC Mode Register (FPSMR) as used by Ethernet. */ #define FCC_PSMR_HBC ((uint)0x80000000) /* Enable heartbeat */ #define FCC_PSMR_FC ((uint)0x40000000) /* Force Collision */ #define FCC_PSMR_SBT ((uint)0x20000000) /* Stop backoff timer */ #define FCC_PSMR_LPB ((uint)0x10000000) /* Local protect. 1 = FDX */ #define FCC_PSMR_LCW ((uint)0x08000000) /* Late collision select */ #define FCC_PSMR_FDE ((uint)0x04000000) /* Full Duplex Enable */ #define FCC_PSMR_MON ((uint)0x02000000) /* RMON Enable */ #define FCC_PSMR_PRO ((uint)0x00400000) /* Promiscuous Enable */ #define FCC_PSMR_FCE ((uint)0x00200000) /* Flow Control Enable */ #define FCC_PSMR_RSH ((uint)0x00100000) /* Receive Short Frames */ #define FCC_PSMR_CAM ((uint)0x00000400) /* CAM enable */ #define FCC_PSMR_BRO ((uint)0x00000200) /* Broadcast pkt discard */ #define FCC_PSMR_ENCRC ((uint)0x00000080) /* Use 32-bit CRC */ /* IIC parameter RAM. */ typedef struct iic { ushort iic_rbase; /* Rx Buffer descriptor base address */ ushort iic_tbase; /* Tx Buffer descriptor base address */ u_char iic_rfcr; /* Rx function code */ u_char iic_tfcr; /* Tx function code */ ushort iic_mrblr; /* Max receive buffer length */ uint iic_rstate; /* Internal */ uint iic_rdp; /* Internal */ ushort iic_rbptr; /* Internal */ ushort iic_rbc; /* Internal */ uint iic_rxtmp; /* Internal */ uint iic_tstate; /* Internal */ uint iic_tdp; /* Internal */ ushort iic_tbptr; /* Internal */ ushort iic_tbc; /* Internal */ uint iic_txtmp; /* Internal */ } iic_t; /* IDMA parameter RAM */ typedef struct idma { ushort ibase; /* IDMA buffer descriptor table base address */ ushort dcm; /* DMA channel mode */ ushort ibdptr; /* IDMA current buffer descriptor pointer */ ushort dpr_buf; /* IDMA transfer buffer base address */ ushort buf_inv; /* internal buffer inventory */ ushort ss_max; /* steady-state maximum transfer size */ ushort dpr_in_ptr; /* write pointer inside the internal buffer */ ushort sts; /* source transfer size */ ushort dpr_out_ptr; /* read pointer inside the internal buffer */ ushort seob; /* source end of burst */ ushort deob; /* destination end of burst */ ushort dts; /* destination transfer size */ ushort ret_add; /* return address when working in ERM=1 mode */ ushort res0; /* reserved */ uint bd_cnt; /* internal byte count */ uint s_ptr; /* source internal data pointer */ uint d_ptr; /* destination internal data pointer */ uint istate; /* internal state */ u_char res1[20]; /* pad to 64-byte length */ } idma_t; /* DMA channel mode bit fields */ #define IDMA_DCM_FB ((ushort)0x8000) /* fly-by mode */ #define IDMA_DCM_LP ((ushort)0x4000) /* low priority */ #define IDMA_DCM_TC2 ((ushort)0x0400) /* value driven on TC[2] */ #define IDMA_DCM_DMA_WRAP_MASK ((ushort)0x01c0) /* mask for DMA wrap */ #define IDMA_DCM_DMA_WRAP_64 ((ushort)0x0000) /* 64-byte DMA xfer buffer */ #define IDMA_DCM_DMA_WRAP_128 ((ushort)0x0040) /* 128-byte DMA xfer buffer */ #define IDMA_DCM_DMA_WRAP_256 ((ushort)0x0080) /* 256-byte DMA xfer buffer */ #define IDMA_DCM_DMA_WRAP_512 ((ushort)0x00c0) /* 512-byte DMA xfer buffer */ #define IDMA_DCM_DMA_WRAP_1024 ((ushort)0x0100) /* 1024-byte DMA xfer buffer */ #define IDMA_DCM_DMA_WRAP_2048 ((ushort)0x0140) /* 2048-byte DMA xfer buffer */ #define IDMA_DCM_SINC ((ushort)0x0020) /* source inc addr */ #define IDMA_DCM_DINC ((ushort)0x0010) /* destination inc addr */ #define IDMA_DCM_ERM ((ushort)0x0008) /* external request mode */ #define IDMA_DCM_DT ((ushort)0x0004) /* DONE treatment */ #define IDMA_DCM_SD_MASK ((ushort)0x0003) /* mask for SD bit field */ #define IDMA_DCM_SD_MEM2MEM ((ushort)0x0000) /* memory-to-memory xfer */ #define IDMA_DCM_SD_PER2MEM ((ushort)0x0002) /* peripheral-to-memory xfer */ #define IDMA_DCM_SD_MEM2PER ((ushort)0x0001) /* memory-to-peripheral xfer */ /* IDMA Buffer Descriptors */ typedef struct idma_bd { uint flags; uint len; /* data length */ uint src; /* source data buffer pointer */ uint dst; /* destination data buffer pointer */ } idma_bd_t; /* IDMA buffer descriptor flag bit fields */ #define IDMA_BD_V ((uint)0x80000000) /* valid */ #define IDMA_BD_W ((uint)0x20000000) /* wrap */ #define IDMA_BD_I ((uint)0x10000000) /* interrupt */ #define IDMA_BD_L ((uint)0x08000000) /* last */ #define IDMA_BD_CM ((uint)0x02000000) /* continuous mode */ #define IDMA_BD_SDN ((uint)0x00400000) /* source done */ #define IDMA_BD_DDN ((uint)0x00200000) /* destination done */ #define IDMA_BD_DGBL ((uint)0x00100000) /* destination global */ #define IDMA_BD_DBO_LE ((uint)0x00040000) /* little-end dest byte order */ #define IDMA_BD_DBO_BE ((uint)0x00080000) /* big-end dest byte order */ #define IDMA_BD_DDTB ((uint)0x00010000) /* destination data bus */ #define IDMA_BD_SGBL ((uint)0x00002000) /* source global */ #define IDMA_BD_SBO_LE ((uint)0x00000800) /* little-end src byte order */ #define IDMA_BD_SBO_BE ((uint)0x00001000) /* big-end src byte order */ #define IDMA_BD_SDTB ((uint)0x00000200) /* source data bus */ /* per-channel IDMA registers */ typedef struct im_idma { u_char idsr; /* IDMAn event status register */ u_char res0[3]; u_char idmr; /* IDMAn event mask register */ u_char res1[3]; } im_idma_t; /* IDMA event register bit fields */ #define IDMA_EVENT_SC ((unsigned char)0x08) /* stop completed */ #define IDMA_EVENT_OB ((unsigned char)0x04) /* out of buffers */ #define IDMA_EVENT_EDN ((unsigned char)0x02) /* external DONE asserted */ #define IDMA_EVENT_BC ((unsigned char)0x01) /* buffer descriptor complete */ /* RISC Controller Configuration Register (RCCR) bit fields */ #define RCCR_TIME ((uint)0x80000000) /* timer enable */ #define RCCR_TIMEP_MASK ((uint)0x3f000000) /* mask for timer period bit field */ #define RCCR_DR0M ((uint)0x00800000) /* IDMA0 request mode */ #define RCCR_DR1M ((uint)0x00400000) /* IDMA1 request mode */ #define RCCR_DR2M ((uint)0x00000080) /* IDMA2 request mode */ #define RCCR_DR3M ((uint)0x00000040) /* IDMA3 request mode */ #define RCCR_DR0QP_MASK ((uint)0x00300000) /* mask for IDMA0 req priority */ #define RCCR_DR0QP_HIGH ((uint)0x00000000) /* IDMA0 has high req priority */ #define RCCR_DR0QP_MED ((uint)0x00100000) /* IDMA0 has medium req priority */ #define RCCR_DR0QP_LOW ((uint)0x00200000) /* IDMA0 has low req priority */ #define RCCR_DR1QP_MASK ((uint)0x00030000) /* mask for IDMA1 req priority */ #define RCCR_DR1QP_HIGH ((uint)0x00000000) /* IDMA1 has high req priority */ #define RCCR_DR1QP_MED ((uint)0x00010000) /* IDMA1 has medium req priority */ #define RCCR_DR1QP_LOW ((uint)0x00020000) /* IDMA1 has low req priority */ #define RCCR_DR2QP_MASK ((uint)0x00000030) /* mask for IDMA2 req priority */ #define RCCR_DR2QP_HIGH ((uint)0x00000000) /* IDMA2 has high req priority */ #define RCCR_DR2QP_MED ((uint)0x00000010) /* IDMA2 has medium req priority */ #define RCCR_DR2QP_LOW ((uint)0x00000020) /* IDMA2 has low req priority */ #define RCCR_DR3QP_MASK ((uint)0x00000003) /* mask for IDMA3 req priority */ #define RCCR_DR3QP_HIGH ((uint)0x00000000) /* IDMA3 has high req priority */ #define RCCR_DR3QP_MED ((uint)0x00000001) /* IDMA3 has medium req priority */ #define RCCR_DR3QP_LOW ((uint)0x00000002) /* IDMA3 has low req priority */ #define RCCR_EIE ((uint)0x00080000) /* external interrupt enable */ #define RCCR_SCD ((uint)0x00040000) /* scheduler configuration */ #define RCCR_ERAM_MASK ((uint)0x0000e000) /* mask for enable RAM microcode */ #define RCCR_ERAM_0KB ((uint)0x00000000) /* use 0KB of dpram for microcode */ #define RCCR_ERAM_2KB ((uint)0x00002000) /* use 2KB of dpram for microcode */ #define RCCR_ERAM_4KB ((uint)0x00004000) /* use 4KB of dpram for microcode */ #define RCCR_ERAM_6KB ((uint)0x00006000) /* use 6KB of dpram for microcode */ #define RCCR_ERAM_8KB ((uint)0x00008000) /* use 8KB of dpram for microcode */ #define RCCR_ERAM_10KB ((uint)0x0000a000) /* use 10KB of dpram for microcode */ #define RCCR_ERAM_12KB ((uint)0x0000c000) /* use 12KB of dpram for microcode */ #define RCCR_EDM0 ((uint)0x00000800) /* DREQ0 edge detect mode */ #define RCCR_EDM1 ((uint)0x00000400) /* DREQ1 edge detect mode */ #define RCCR_EDM2 ((uint)0x00000200) /* DREQ2 edge detect mode */ #define RCCR_EDM3 ((uint)0x00000100) /* DREQ3 edge detect mode */ #define RCCR_DEM01 ((uint)0x00000008) /* DONE0/DONE1 edge detect mode */ #define RCCR_DEM23 ((uint)0x00000004) /* DONE2/DONE3 edge detect mode */ /*----------------------------------------------------------------------- * CMXFCR - CMX FCC Clock Route Register */ #define CMXFCR_FC1 0x40000000 /* FCC1 connection */ #define CMXFCR_RF1CS_MSK 0x38000000 /* Receive FCC1 Clock Source Mask */ #define CMXFCR_TF1CS_MSK 0x07000000 /* Transmit FCC1 Clock Source Mask */ #define CMXFCR_FC2 0x00400000 /* FCC2 connection */ #define CMXFCR_RF2CS_MSK 0x00380000 /* Receive FCC2 Clock Source Mask */ #define CMXFCR_TF2CS_MSK 0x00070000 /* Transmit FCC2 Clock Source Mask */ #define CMXFCR_FC3 0x00004000 /* FCC3 connection */ #define CMXFCR_RF3CS_MSK 0x00003800 /* Receive FCC3 Clock Source Mask */ #define CMXFCR_TF3CS_MSK 0x00000700 /* Transmit FCC3 Clock Source Mask */ #define CMXFCR_RF1CS_BRG5 0x00000000 /* Receive FCC1 Clock Source is BRG5 */ #define CMXFCR_RF1CS_BRG6 0x08000000 /* Receive FCC1 Clock Source is BRG6 */ #define CMXFCR_RF1CS_BRG7 0x10000000 /* Receive FCC1 Clock Source is BRG7 */ #define CMXFCR_RF1CS_BRG8 0x18000000 /* Receive FCC1 Clock Source is BRG8 */ #define CMXFCR_RF1CS_CLK9 0x20000000 /* Receive FCC1 Clock Source is CLK9 */ #define CMXFCR_RF1CS_CLK10 0x28000000 /* Receive FCC1 Clock Source is CLK10 */ #define CMXFCR_RF1CS_CLK11 0x30000000 /* Receive FCC1 Clock Source is CLK11 */ #define CMXFCR_RF1CS_CLK12 0x38000000 /* Receive FCC1 Clock Source is CLK12 */ #define CMXFCR_TF1CS_BRG5 0x00000000 /* Transmit FCC1 Clock Source is BRG5 */ #define CMXFCR_TF1CS_BRG6 0x01000000 /* Transmit FCC1 Clock Source is BRG6 */ #define CMXFCR_TF1CS_BRG7 0x02000000 /* Transmit FCC1 Clock Source is BRG7 */ #define CMXFCR_TF1CS_BRG8 0x03000000 /* Transmit FCC1 Clock Source is BRG8 */ #define CMXFCR_TF1CS_CLK9 0x04000000 /* Transmit FCC1 Clock Source is CLK9 */ #define CMXFCR_TF1CS_CLK10 0x05000000 /* Transmit FCC1 Clock Source is CLK10 */ #define CMXFCR_TF1CS_CLK11 0x06000000 /* Transmit FCC1 Clock Source is CLK11 */ #define CMXFCR_TF1CS_CLK12 0x07000000 /* Transmit FCC1 Clock Source is CLK12 */ #define CMXFCR_RF2CS_BRG5 0x00000000 /* Receive FCC2 Clock Source is BRG5 */ #define CMXFCR_RF2CS_BRG6 0x00080000 /* Receive FCC2 Clock Source is BRG6 */ #define CMXFCR_RF2CS_BRG7 0x00100000 /* Receive FCC2 Clock Source is BRG7 */ #define CMXFCR_RF2CS_BRG8 0x00180000 /* Receive FCC2 Clock Source is BRG8 */ #define CMXFCR_RF2CS_CLK13 0x00200000 /* Receive FCC2 Clock Source is CLK13 */ #define CMXFCR_RF2CS_CLK14 0x00280000 /* Receive FCC2 Clock Source is CLK14 */ #define CMXFCR_RF2CS_CLK15 0x00300000 /* Receive FCC2 Clock Source is CLK15 */ #define CMXFCR_RF2CS_CLK16 0x00380000 /* Receive FCC2 Clock Source is CLK16 */ #define CMXFCR_TF2CS_BRG5 0x00000000 /* Transmit FCC2 Clock Source is BRG5 */ #define CMXFCR_TF2CS_BRG6 0x00010000 /* Transmit FCC2 Clock Source is BRG6 */ #define CMXFCR_TF2CS_BRG7 0x00020000 /* Transmit FCC2 Clock Source is BRG7 */ #define CMXFCR_TF2CS_BRG8 0x00030000 /* Transmit FCC2 Clock Source is BRG8 */ #define CMXFCR_TF2CS_CLK13 0x00040000 /* Transmit FCC2 Clock Source is CLK13 */ #define CMXFCR_TF2CS_CLK14 0x00050000 /* Transmit FCC2 Clock Source is CLK14 */ #define CMXFCR_TF2CS_CLK15 0x00060000 /* Transmit FCC2 Clock Source is CLK15 */ #define CMXFCR_TF2CS_CLK16 0x00070000 /* Transmit FCC2 Clock Source is CLK16 */ #define CMXFCR_RF3CS_BRG5 0x00000000 /* Receive FCC3 Clock Source is BRG5 */ #define CMXFCR_RF3CS_BRG6 0x00000800 /* Receive FCC3 Clock Source is BRG6 */ #define CMXFCR_RF3CS_BRG7 0x00001000 /* Receive FCC3 Clock Source is BRG7 */ #define CMXFCR_RF3CS_BRG8 0x00001800 /* Receive FCC3 Clock Source is BRG8 */ #define CMXFCR_RF3CS_CLK13 0x00002000 /* Receive FCC3 Clock Source is CLK13 */ #define CMXFCR_RF3CS_CLK14 0x00002800 /* Receive FCC3 Clock Source is CLK14 */ #define CMXFCR_RF3CS_CLK15 0x00003000 /* Receive FCC3 Clock Source is CLK15 */ #define CMXFCR_RF3CS_CLK16 0x00003800 /* Receive FCC3 Clock Source is CLK16 */ #define CMXFCR_TF3CS_BRG5 0x00000000 /* Transmit FCC3 Clock Source is BRG5 */ #define CMXFCR_TF3CS_BRG6 0x00000100 /* Transmit FCC3 Clock Source is BRG6 */ #define CMXFCR_TF3CS_BRG7 0x00000200 /* Transmit FCC3 Clock Source is BRG7 */ #define CMXFCR_TF3CS_BRG8 0x00000300 /* Transmit FCC3 Clock Source is BRG8 */ #define CMXFCR_TF3CS_CLK13 0x00000400 /* Transmit FCC3 Clock Source is CLK13 */ #define CMXFCR_TF3CS_CLK14 0x00000500 /* Transmit FCC3 Clock Source is CLK14 */ #define CMXFCR_TF3CS_CLK15 0x00000600 /* Transmit FCC3 Clock Source is CLK15 */ #define CMXFCR_TF3CS_CLK16 0x00000700 /* Transmit FCC3 Clock Source is CLK16 */ /*----------------------------------------------------------------------- * CMXSCR - CMX SCC Clock Route Register */ #define CMXSCR_GR1 0x80000000 /* Grant Support of SCC1 */ #define CMXSCR_SC1 0x40000000 /* SCC1 connection */ #define CMXSCR_RS1CS_MSK 0x38000000 /* Receive SCC1 Clock Source Mask */ #define CMXSCR_TS1CS_MSK 0x07000000 /* Transmit SCC1 Clock Source Mask */ #define CMXSCR_GR2 0x00800000 /* Grant Support of SCC2 */ #define CMXSCR_SC2 0x00400000 /* SCC2 connection */ #define CMXSCR_RS2CS_MSK 0x00380000 /* Receive SCC2 Clock Source Mask */ #define CMXSCR_TS2CS_MSK 0x00070000 /* Transmit SCC2 Clock Source Mask */ #define CMXSCR_GR3 0x00008000 /* Grant Support of SCC3 */ #define CMXSCR_SC3 0x00004000 /* SCC3 connection */ #define CMXSCR_RS3CS_MSK 0x00003800 /* Receive SCC3 Clock Source Mask */ #define CMXSCR_TS3CS_MSK 0x00000700 /* Transmit SCC3 Clock Source Mask */ #define CMXSCR_GR4 0x00000080 /* Grant Support of SCC4 */ #define CMXSCR_SC4 0x00000040 /* SCC4 connection */ #define CMXSCR_RS4CS_MSK 0x00000038 /* Receive SCC4 Clock Source Mask */ #define CMXSCR_TS4CS_MSK 0x00000007 /* Transmit SCC4 Clock Source Mask */ #define CMXSCR_RS1CS_BRG1 0x00000000 /* SCC1 Rx Clock Source is BRG1 */ #define CMXSCR_RS1CS_BRG2 0x08000000 /* SCC1 Rx Clock Source is BRG2 */ #define CMXSCR_RS1CS_BRG3 0x10000000 /* SCC1 Rx Clock Source is BRG3 */ #define CMXSCR_RS1CS_BRG4 0x18000000 /* SCC1 Rx Clock Source is BRG4 */ #define CMXSCR_RS1CS_CLK11 0x20000000 /* SCC1 Rx Clock Source is CLK11 */ #define CMXSCR_RS1CS_CLK12 0x28000000 /* SCC1 Rx Clock Source is CLK12 */ #define CMXSCR_RS1CS_CLK3 0x30000000 /* SCC1 Rx Clock Source is CLK3 */ #define CMXSCR_RS1CS_CLK4 0x38000000 /* SCC1 Rx Clock Source is CLK4 */ #define CMXSCR_TS1CS_BRG1 0x00000000 /* SCC1 Tx Clock Source is BRG1 */ #define CMXSCR_TS1CS_BRG2 0x01000000 /* SCC1 Tx Clock Source is BRG2 */ #define CMXSCR_TS1CS_BRG3 0x02000000 /* SCC1 Tx Clock Source is BRG3 */ #define CMXSCR_TS1CS_BRG4 0x03000000 /* SCC1 Tx Clock Source is BRG4 */ #define CMXSCR_TS1CS_CLK11 0x04000000 /* SCC1 Tx Clock Source is CLK11 */ #define CMXSCR_TS1CS_CLK12 0x05000000 /* SCC1 Tx Clock Source is CLK12 */ #define CMXSCR_TS1CS_CLK3 0x06000000 /* SCC1 Tx Clock Source is CLK3 */ #define CMXSCR_TS1CS_CLK4 0x07000000 /* SCC1 Tx Clock Source is CLK4 */ #define CMXSCR_RS2CS_BRG1 0x00000000 /* SCC2 Rx Clock Source is BRG1 */ #define CMXSCR_RS2CS_BRG2 0x00080000 /* SCC2 Rx Clock Source is BRG2 */ #define CMXSCR_RS2CS_BRG3 0x00100000 /* SCC2 Rx Clock Source is BRG3 */ #define CMXSCR_RS2CS_BRG4 0x00180000 /* SCC2 Rx Clock Source is BRG4 */ #define CMXSCR_RS2CS_CLK11 0x00200000 /* SCC2 Rx Clock Source is CLK11 */ #define CMXSCR_RS2CS_CLK12 0x00280000 /* SCC2 Rx Clock Source is CLK12 */ #define CMXSCR_RS2CS_CLK3 0x00300000 /* SCC2 Rx Clock Source is CLK3 */ #define CMXSCR_RS2CS_CLK4 0x00380000 /* SCC2 Rx Clock Source is CLK4 */ #define CMXSCR_TS2CS_BRG1 0x00000000 /* SCC2 Tx Clock Source is BRG1 */ #define CMXSCR_TS2CS_BRG2 0x00010000 /* SCC2 Tx Clock Source is BRG2 */ #define CMXSCR_TS2CS_BRG3 0x00020000 /* SCC2 Tx Clock Source is BRG3 */ #define CMXSCR_TS2CS_BRG4 0x00030000 /* SCC2 Tx Clock Source is BRG4 */ #define CMXSCR_TS2CS_CLK11 0x00040000 /* SCC2 Tx Clock Source is CLK11 */ #define CMXSCR_TS2CS_CLK12 0x00050000 /* SCC2 Tx Clock Source is CLK12 */ #define CMXSCR_TS2CS_CLK3 0x00060000 /* SCC2 Tx Clock Source is CLK3 */ #define CMXSCR_TS2CS_CLK4 0x00070000 /* SCC2 Tx Clock Source is CLK4 */ #define CMXSCR_RS3CS_BRG1 0x00000000 /* SCC3 Rx Clock Source is BRG1 */ #define CMXSCR_RS3CS_BRG2 0x00000800 /* SCC3 Rx Clock Source is BRG2 */ #define CMXSCR_RS3CS_BRG3 0x00001000 /* SCC3 Rx Clock Source is BRG3 */ #define CMXSCR_RS3CS_BRG4 0x00001800 /* SCC3 Rx Clock Source is BRG4 */ #define CMXSCR_RS3CS_CLK5 0x00002000 /* SCC3 Rx Clock Source is CLK5 */ #define CMXSCR_RS3CS_CLK6 0x00002800 /* SCC3 Rx Clock Source is CLK6 */ #define CMXSCR_RS3CS_CLK7 0x00003000 /* SCC3 Rx Clock Source is CLK7 */ #define CMXSCR_RS3CS_CLK8 0x00003800 /* SCC3 Rx Clock Source is CLK8 */ #define CMXSCR_TS3CS_BRG1 0x00000000 /* SCC3 Tx Clock Source is BRG1 */ #define CMXSCR_TS3CS_BRG2 0x00000100 /* SCC3 Tx Clock Source is BRG2 */ #define CMXSCR_TS3CS_BRG3 0x00000200 /* SCC3 Tx Clock Source is BRG3 */ #define CMXSCR_TS3CS_BRG4 0x00000300 /* SCC3 Tx Clock Source is BRG4 */ #define CMXSCR_TS3CS_CLK5 0x00000400 /* SCC3 Tx Clock Source is CLK5 */ #define CMXSCR_TS3CS_CLK6 0x00000500 /* SCC3 Tx Clock Source is CLK6 */ #define CMXSCR_TS3CS_CLK7 0x00000600 /* SCC3 Tx Clock Source is CLK7 */ #define CMXSCR_TS3CS_CLK8 0x00000700 /* SCC3 Tx Clock Source is CLK8 */ #define CMXSCR_RS4CS_BRG1 0x00000000 /* SCC4 Rx Clock Source is BRG1 */ #define CMXSCR_RS4CS_BRG2 0x00000008 /* SCC4 Rx Clock Source is BRG2 */ #define CMXSCR_RS4CS_BRG3 0x00000010 /* SCC4 Rx Clock Source is BRG3 */ #define CMXSCR_RS4CS_BRG4 0x00000018 /* SCC4 Rx Clock Source is BRG4 */ #define CMXSCR_RS4CS_CLK5 0x00000020 /* SCC4 Rx Clock Source is CLK5 */ #define CMXSCR_RS4CS_CLK6 0x00000028 /* SCC4 Rx Clock Source is CLK6 */ #define CMXSCR_RS4CS_CLK7 0x00000030 /* SCC4 Rx Clock Source is CLK7 */ #define CMXSCR_RS4CS_CLK8 0x00000038 /* SCC4 Rx Clock Source is CLK8 */ #define CMXSCR_TS4CS_BRG1 0x00000000 /* SCC4 Tx Clock Source is BRG1 */ #define CMXSCR_TS4CS_BRG2 0x00000001 /* SCC4 Tx Clock Source is BRG2 */ #define CMXSCR_TS4CS_BRG3 0x00000002 /* SCC4 Tx Clock Source is BRG3 */ #define CMXSCR_TS4CS_BRG4 0x00000003 /* SCC4 Tx Clock Source is BRG4 */ #define CMXSCR_TS4CS_CLK5 0x00000004 /* SCC4 Tx Clock Source is CLK5 */ #define CMXSCR_TS4CS_CLK6 0x00000005 /* SCC4 Tx Clock Source is CLK6 */ #define CMXSCR_TS4CS_CLK7 0x00000006 /* SCC4 Tx Clock Source is CLK7 */ #define CMXSCR_TS4CS_CLK8 0x00000007 /* SCC4 Tx Clock Source is CLK8 */ /*----------------------------------------------------------------------- * SIUMCR - SIU Module Configuration Register 4-31 */ #define SIUMCR_BBD 0x80000000 /* Bus Busy Disable */ #define SIUMCR_ESE 0x40000000 /* External Snoop Enable */ #define SIUMCR_PBSE 0x20000000 /* Parity Byte Select Enable */ #define SIUMCR_CDIS 0x10000000 /* Core Disable */ #define SIUMCR_DPPC00 0x00000000 /* Data Parity Pins Configuration*/ #define SIUMCR_DPPC01 0x04000000 /* - " - */ #define SIUMCR_DPPC10 0x08000000 /* - " - */ #define SIUMCR_DPPC11 0x0c000000 /* - " - */ #define SIUMCR_L2CPC00 0x00000000 /* L2 Cache Pins Configuration */ #define SIUMCR_L2CPC01 0x01000000 /* - " - */ #define SIUMCR_L2CPC10 0x02000000 /* - " - */ #define SIUMCR_L2CPC11 0x03000000 /* - " - */ #define SIUMCR_LBPC00 0x00000000 /* Local Bus Pins Configuration */ #define SIUMCR_LBPC01 0x00400000 /* - " - */ #define SIUMCR_LBPC10 0x00800000 /* - " - */ #define SIUMCR_LBPC11 0x00c00000 /* - " - */ #define SIUMCR_APPC00 0x00000000 /* Address Parity Pins Configuration*/ #define SIUMCR_APPC01 0x00100000 /* - " - */ #define SIUMCR_APPC10 0x00200000 /* - " - */ #define SIUMCR_APPC11 0x00300000 /* - " - */ #define SIUMCR_CS10PC00 0x00000000 /* CS10 Pin Configuration */ #define SIUMCR_CS10PC01 0x00040000 /* - " - */ #define SIUMCR_CS10PC10 0x00080000 /* - " - */ #define SIUMCR_CS10PC11 0x000c0000 /* - " - */ #define SIUMCR_BCTLC00 0x00000000 /* Buffer Control Configuration */ #define SIUMCR_BCTLC01 0x00010000 /* - " - */ #define SIUMCR_BCTLC10 0x00020000 /* - " - */ #define SIUMCR_BCTLC11 0x00030000 /* - " - */ #define SIUMCR_MMR00 0x00000000 /* Mask Masters Requests */ #define SIUMCR_MMR01 0x00004000 /* - " - */ #define SIUMCR_MMR10 0x00008000 /* - " - */ #define SIUMCR_MMR11 0x0000c000 /* - " - */ #define SIUMCR_LPBSE 0x00002000 /* LocalBus Parity Byte Select Enable*/ /*----------------------------------------------------------------------- * SCCR - System Clock Control Register 9-8 */ #define SCCR_PCI_MODE 0x00000100 /* PCI Mode */ #define SCCR_PCI_MODCK 0x00000080 /* Value of PCI_MODCK pin */ #define SCCR_PCIDF_MSK 0x00000078 /* PCI division factor */ #define SCCR_PCIDF_SHIFT 3 #ifndef CPM_IMMR_OFFSET #define CPM_IMMR_OFFSET 0x101a8 #endif #define FCC_PSMR_RMII ((uint)0x00020000) /* Use RMII interface */ /* FCC iop & clock configuration. BSP code is responsible to define Fx_RXCLK & Fx_TXCLK * in order to use clock-computing stuff below for the FCC x */ /* Automatically generates register configurations */ #define PC_CLK(x) ((uint)(1<<(x-1))) /* FCC CLK I/O ports */ #define CMXFCR_RF1CS(x) ((uint)((x-5)<<27)) /* FCC1 Receive Clock Source */ #define CMXFCR_TF1CS(x) ((uint)((x-5)<<24)) /* FCC1 Transmit Clock Source */ #define CMXFCR_RF2CS(x) ((uint)((x-9)<<19)) /* FCC2 Receive Clock Source */ #define CMXFCR_TF2CS(x) ((uint)((x-9)<<16)) /* FCC2 Transmit Clock Source */ #define CMXFCR_RF3CS(x) ((uint)((x-9)<<11)) /* FCC3 Receive Clock Source */ #define CMXFCR_TF3CS(x) ((uint)((x-9)<<8)) /* FCC3 Transmit Clock Source */ #define PC_F1RXCLK PC_CLK(F1_RXCLK) #define PC_F1TXCLK PC_CLK(F1_TXCLK) #define CMX1_CLK_ROUTE (CMXFCR_RF1CS(F1_RXCLK) | CMXFCR_TF1CS(F1_TXCLK)) #define CMX1_CLK_MASK ((uint)0xff000000) #define PC_F2RXCLK PC_CLK(F2_RXCLK) #define PC_F2TXCLK PC_CLK(F2_TXCLK) #define CMX2_CLK_ROUTE (CMXFCR_RF2CS(F2_RXCLK) | CMXFCR_TF2CS(F2_TXCLK)) #define CMX2_CLK_MASK ((uint)0x00ff0000) #define PC_F3RXCLK PC_CLK(F3_RXCLK) #define PC_F3TXCLK PC_CLK(F3_TXCLK) #define CMX3_CLK_ROUTE (CMXFCR_RF3CS(F3_RXCLK) | CMXFCR_TF3CS(F3_TXCLK)) #define CMX3_CLK_MASK ((uint)0x0000ff00) #define CPMUX_CLK_MASK (CMX3_CLK_MASK | CMX2_CLK_MASK) #define CPMUX_CLK_ROUTE (CMX3_CLK_ROUTE | CMX2_CLK_ROUTE) #define CLK_TRX (PC_F3TXCLK | PC_F3RXCLK | PC_F2TXCLK | PC_F2RXCLK) /* I/O Pin assignment for FCC1. I don't yet know the best way to do this, * but there is little variation among the choices. */ #define PA1_COL 0x00000001U #define PA1_CRS 0x00000002U #define PA1_TXER 0x00000004U #define PA1_TXEN 0x00000008U #define PA1_RXDV 0x00000010U #define PA1_RXER 0x00000020U #define PA1_TXDAT 0x00003c00U #define PA1_RXDAT 0x0003c000U #define PA1_PSORA0 (PA1_RXDAT | PA1_TXDAT) #define PA1_PSORA1 (PA1_COL | PA1_CRS | PA1_TXER | PA1_TXEN | \ PA1_RXDV | PA1_RXER) #define PA1_DIRA0 (PA1_RXDAT | PA1_CRS | PA1_COL | PA1_RXER | PA1_RXDV) #define PA1_DIRA1 (PA1_TXDAT | PA1_TXEN | PA1_TXER) /* I/O Pin assignment for FCC2. I don't yet know the best way to do this, * but there is little variation among the choices. */ #define PB2_TXER 0x00000001U #define PB2_RXDV 0x00000002U #define PB2_TXEN 0x00000004U #define PB2_RXER 0x00000008U #define PB2_COL 0x00000010U #define PB2_CRS 0x00000020U #define PB2_TXDAT 0x000003c0U #define PB2_RXDAT 0x00003c00U #define PB2_PSORB0 (PB2_RXDAT | PB2_TXDAT | PB2_CRS | PB2_COL | \ PB2_RXER | PB2_RXDV | PB2_TXER) #define PB2_PSORB1 (PB2_TXEN) #define PB2_DIRB0 (PB2_RXDAT | PB2_CRS | PB2_COL | PB2_RXER | PB2_RXDV) #define PB2_DIRB1 (PB2_TXDAT | PB2_TXEN | PB2_TXER) /* I/O Pin assignment for FCC3. I don't yet know the best way to do this, * but there is little variation among the choices. */ #define PB3_RXDV 0x00004000U #define PB3_RXER 0x00008000U #define PB3_TXER 0x00010000U #define PB3_TXEN 0x00020000U #define PB3_COL 0x00040000U #define PB3_CRS 0x00080000U #define PB3_TXDAT 0x0f000000U #define PC3_TXDAT 0x00000010U #define PB3_RXDAT 0x00f00000U #define PB3_PSORB0 (PB3_RXDAT | PB3_TXDAT | PB3_CRS | PB3_COL | \ PB3_RXER | PB3_RXDV | PB3_TXER | PB3_TXEN) #define PB3_PSORB1 0 #define PB3_DIRB0 (PB3_RXDAT | PB3_CRS | PB3_COL | PB3_RXER | PB3_RXDV) #define PB3_DIRB1 (PB3_TXDAT | PB3_TXEN | PB3_TXER) #define PC3_DIRC1 (PC3_TXDAT) /* Handy macro to specify mem for FCCs*/ #define FCC_MEM_OFFSET(x) (CPM_FCC_SPECIAL_BASE + (x*128)) #define FCC1_MEM_OFFSET FCC_MEM_OFFSET(0) #define FCC2_MEM_OFFSET FCC_MEM_OFFSET(1) #define FCC3_MEM_OFFSET FCC_MEM_OFFSET(2) /* Pipeline Maximum Depth */ #define MPC82XX_BCR_PLDP 0x00800000 /* Clocks and GRG's */ enum cpm_clk_dir { CPM_CLK_RX, CPM_CLK_TX, CPM_CLK_RTX }; enum cpm_clk_target { CPM_CLK_SCC1, CPM_CLK_SCC2, CPM_CLK_SCC3, CPM_CLK_SCC4, CPM_CLK_FCC1, CPM_CLK_FCC2, CPM_CLK_FCC3, CPM_CLK_SMC1, CPM_CLK_SMC2, }; enum cpm_clk { CPM_CLK_NONE = 0, CPM_BRG1, /* Baud Rate Generator 1 */ CPM_BRG2, /* Baud Rate Generator 2 */ CPM_BRG3, /* Baud Rate Generator 3 */ CPM_BRG4, /* Baud Rate Generator 4 */ CPM_BRG5, /* Baud Rate Generator 5 */ CPM_BRG6, /* Baud Rate Generator 6 */ CPM_BRG7, /* Baud Rate Generator 7 */ CPM_BRG8, /* Baud Rate Generator 8 */ CPM_CLK1, /* Clock 1 */ CPM_CLK2, /* Clock 2 */ CPM_CLK3, /* Clock 3 */ CPM_CLK4, /* Clock 4 */ CPM_CLK5, /* Clock 5 */ CPM_CLK6, /* Clock 6 */ CPM_CLK7, /* Clock 7 */ CPM_CLK8, /* Clock 8 */ CPM_CLK9, /* Clock 9 */ CPM_CLK10, /* Clock 10 */ CPM_CLK11, /* Clock 11 */ CPM_CLK12, /* Clock 12 */ CPM_CLK13, /* Clock 13 */ CPM_CLK14, /* Clock 14 */ CPM_CLK15, /* Clock 15 */ CPM_CLK16, /* Clock 16 */ CPM_CLK17, /* Clock 17 */ CPM_CLK18, /* Clock 18 */ CPM_CLK19, /* Clock 19 */ CPM_CLK20, /* Clock 20 */ CPM_CLK_DUMMY }; int __init cpm2_clk_setup(enum cpm_clk_target target, int clock, int mode); int __init cpm2_smc_clk_setup(enum cpm_clk_target target, int clock); #define CPM_PIN_INPUT 0 #define CPM_PIN_OUTPUT 1 #define CPM_PIN_PRIMARY 0 #define CPM_PIN_SECONDARY 2 #define CPM_PIN_GPIO 4 #define CPM_PIN_OPENDRAIN 8 void __init cpm2_set_pin(int port, int pin, int flags); #endif /* __CPM2__ */ #endif /* __KERNEL__ */
© 2026 UnknownSec