shell bypass 403
UnknownSec Shell
:
/
usr
/
src
/
linux-headers-6.8.0-83-generic
/
arch
/
mips
/
include
/
asm
/
sibyte
/ [
drwxr-xr-x
]
upload
mass deface
mass delete
console
info server
name :
sb1250_regs.h
/* SPDX-License-Identifier: GPL-2.0-or-later */ /* ********************************************************************* * SB1250 Board Support Package * * Register Definitions File: sb1250_regs.h * * This module contains the addresses of the on-chip peripherals * on the SB1250. * * SB1250 specification level: 01/02/2002 * ********************************************************************* * * Copyright 2000,2001,2002,2003 * Broadcom Corporation. All rights reserved. * ********************************************************************* */ #ifndef _SB1250_REGS_H #define _SB1250_REGS_H #include <asm/sibyte/sb1250_defs.h> /* ********************************************************************* * Some general notes: * * For the most part, when there is more than one peripheral * of the same type on the SOC, the constants below will be * offsets from the base of each peripheral. For example, * the MAC registers are described as offsets from the first * MAC register, and there will be a MAC_REGISTER() macro * to calculate the base address of a given MAC. * * The information in this file is based on the SB1250 SOC * manual version 0.2, July 2000. ********************************************************************* */ /* ********************************************************************* * Memory Controller Registers ********************************************************************* */ /* * XXX: can't remove MC base 0 if 112x, since it's used by other macros, * since there is one reg there (but it could get its addr/offset constant). */ #if SIBYTE_HDR_FEATURE_1250_112x /* This MC only on 1250 & 112x */ #define A_MC_BASE_0 0x0010051000 #define A_MC_BASE_1 0x0010052000 #define MC_REGISTER_SPACING 0x1000 #define A_MC_BASE(ctlid) ((ctlid)*MC_REGISTER_SPACING+A_MC_BASE_0) #define A_MC_REGISTER(ctlid, reg) (A_MC_BASE(ctlid)+(reg)) #define R_MC_CONFIG 0x0000000100 #define R_MC_DRAMCMD 0x0000000120 #define R_MC_DRAMMODE 0x0000000140 #define R_MC_TIMING1 0x0000000160 #define R_MC_TIMING2 0x0000000180 #define R_MC_CS_START 0x00000001A0 #define R_MC_CS_END 0x00000001C0 #define R_MC_CS_INTERLEAVE 0x00000001E0 #define S_MC_CS_STARTEND 16 #define R_MC_CSX_BASE 0x0000000200 #define R_MC_CSX_ROW 0x0000000000 /* relative to CSX_BASE, above */ #define R_MC_CSX_COL 0x0000000020 /* relative to CSX_BASE, above */ #define R_MC_CSX_BA 0x0000000040 /* relative to CSX_BASE, above */ #define MC_CSX_SPACING 0x0000000060 /* relative to CSX_BASE, above */ #define R_MC_CS0_ROW 0x0000000200 #define R_MC_CS0_COL 0x0000000220 #define R_MC_CS0_BA 0x0000000240 #define R_MC_CS1_ROW 0x0000000260 #define R_MC_CS1_COL 0x0000000280 #define R_MC_CS1_BA 0x00000002A0 #define R_MC_CS2_ROW 0x00000002C0 #define R_MC_CS2_COL 0x00000002E0 #define R_MC_CS2_BA 0x0000000300 #define R_MC_CS3_ROW 0x0000000320 #define R_MC_CS3_COL 0x0000000340 #define R_MC_CS3_BA 0x0000000360 #define R_MC_CS_ATTR 0x0000000380 #define R_MC_TEST_DATA 0x0000000400 #define R_MC_TEST_ECC 0x0000000420 #define R_MC_MCLK_CFG 0x0000000500 #endif /* 1250 & 112x */ /* ********************************************************************* * L2 Cache Control Registers ********************************************************************* */ #if SIBYTE_HDR_FEATURE_1250_112x /* This L2C only on 1250/112x */ #define A_L2_READ_TAG 0x0010040018 #define A_L2_ECC_TAG 0x0010040038 #if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1) #define A_L2_READ_MISC 0x0010040058 #endif /* 1250 PASS3 || 112x PASS1 */ #define A_L2_WAY_DISABLE 0x0010041000 #define A_L2_MAKEDISABLE(x) (A_L2_WAY_DISABLE | (((~(x))&0x0F) << 8)) #define A_L2_MGMT_TAG_BASE 0x00D0000000 #if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1) #define A_L2_CACHE_DISABLE 0x0010042000 #define A_L2_MAKECACHEDISABLE(x) (A_L2_CACHE_DISABLE | (((x)&0x0F) << 8)) #define A_L2_MISC_CONFIG 0x0010043000 #endif /* 1250 PASS2 || 112x PASS1 */ /* Backward-compatibility definitions. */ /* XXX: discourage people from using these constants. */ #define A_L2_READ_ADDRESS A_L2_READ_TAG #define A_L2_EEC_ADDRESS A_L2_ECC_TAG #endif /* ********************************************************************* * PCI Interface Registers ********************************************************************* */ #if SIBYTE_HDR_FEATURE_1250_112x /* This PCI/HT only on 1250/112x */ #define A_PCI_TYPE00_HEADER 0x00DE000000 #define A_PCI_TYPE01_HEADER 0x00DE000800 #endif /* ********************************************************************* * Ethernet DMA and MACs ********************************************************************* */ #define A_MAC_BASE_0 0x0010064000 #define A_MAC_BASE_1 0x0010065000 #if SIBYTE_HDR_FEATURE_CHIP(1250) #define A_MAC_BASE_2 0x0010066000 #endif /* 1250 */ #define MAC_SPACING 0x1000 #define MAC_DMA_TXRX_SPACING 0x0400 #define MAC_DMA_CHANNEL_SPACING 0x0100 #define DMA_RX 0 #define DMA_TX 1 #define MAC_NUM_DMACHAN 2 /* channels per direction */ /* XXX: not correct; depends on SOC type. */ #define MAC_NUM_PORTS 3 #define A_MAC_CHANNEL_BASE(macnum) \ (A_MAC_BASE_0 + \ MAC_SPACING*(macnum)) #define A_MAC_REGISTER(macnum,reg) \ (A_MAC_BASE_0 + \ MAC_SPACING*(macnum) + (reg)) #define R_MAC_DMA_CHANNELS 0x800 /* Relative to A_MAC_CHANNEL_BASE */ #define A_MAC_DMA_CHANNEL_BASE(macnum, txrx, chan) \ ((A_MAC_CHANNEL_BASE(macnum)) + \ R_MAC_DMA_CHANNELS + \ (MAC_DMA_TXRX_SPACING*(txrx)) + \ (MAC_DMA_CHANNEL_SPACING*(chan))) #define R_MAC_DMA_CHANNEL_BASE(txrx, chan) \ (R_MAC_DMA_CHANNELS + \ (MAC_DMA_TXRX_SPACING*(txrx)) + \ (MAC_DMA_CHANNEL_SPACING*(chan))) #define A_MAC_DMA_REGISTER(macnum, txrx, chan, reg) \ (A_MAC_DMA_CHANNEL_BASE(macnum, txrx, chan) + \ (reg)) #define R_MAC_DMA_REGISTER(txrx, chan, reg) \ (R_MAC_DMA_CHANNEL_BASE(txrx, chan) + \ (reg)) /* * DMA channel registers, relative to A_MAC_DMA_CHANNEL_BASE */ #define R_MAC_DMA_CONFIG0 0x00000000 #define R_MAC_DMA_CONFIG1 0x00000008 #define R_MAC_DMA_DSCR_BASE 0x00000010 #define R_MAC_DMA_DSCR_CNT 0x00000018 #define R_MAC_DMA_CUR_DSCRA 0x00000020 #define R_MAC_DMA_CUR_DSCRB 0x00000028 #define R_MAC_DMA_CUR_DSCRADDR 0x00000030 #if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1) #define R_MAC_DMA_OODPKTLOST_RX 0x00000038 /* rx only */ #endif /* 1250 PASS3 || 112x PASS1 */ /* * RMON Counters */ #define R_MAC_RMON_TX_BYTES 0x00000000 #define R_MAC_RMON_COLLISIONS 0x00000008 #define R_MAC_RMON_LATE_COL 0x00000010 #define R_MAC_RMON_EX_COL 0x00000018 #define R_MAC_RMON_FCS_ERROR 0x00000020 #define R_MAC_RMON_TX_ABORT 0x00000028 /* Counter #6 (0x30) now reserved */ #define R_MAC_RMON_TX_BAD 0x00000038 #define R_MAC_RMON_TX_GOOD 0x00000040 #define R_MAC_RMON_TX_RUNT 0x00000048 #define R_MAC_RMON_TX_OVERSIZE 0x00000050 #define R_MAC_RMON_RX_BYTES 0x00000080 #define R_MAC_RMON_RX_MCAST 0x00000088 #define R_MAC_RMON_RX_BCAST 0x00000090 #define R_MAC_RMON_RX_BAD 0x00000098 #define R_MAC_RMON_RX_GOOD 0x000000A0 #define R_MAC_RMON_RX_RUNT 0x000000A8 #define R_MAC_RMON_RX_OVERSIZE 0x000000B0 #define R_MAC_RMON_RX_FCS_ERROR 0x000000B8 #define R_MAC_RMON_RX_LENGTH_ERROR 0x000000C0 #define R_MAC_RMON_RX_CODE_ERROR 0x000000C8 #define R_MAC_RMON_RX_ALIGN_ERROR 0x000000D0 /* Updated to spec 0.2 */ #define R_MAC_CFG 0x00000100 #define R_MAC_THRSH_CFG 0x00000108 #define R_MAC_VLANTAG 0x00000110 #define R_MAC_FRAMECFG 0x00000118 #define R_MAC_EOPCNT 0x00000120 #define R_MAC_FIFO_PTRS 0x00000128 #define R_MAC_ADFILTER_CFG 0x00000200 #define R_MAC_ETHERNET_ADDR 0x00000208 #define R_MAC_PKT_TYPE 0x00000210 #if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480) #define R_MAC_ADMASK0 0x00000218 #define R_MAC_ADMASK1 0x00000220 #endif /* 1250 PASS3 || 112x PASS1 || 1480 */ #define R_MAC_HASH_BASE 0x00000240 #define R_MAC_ADDR_BASE 0x00000280 #define R_MAC_CHLO0_BASE 0x00000300 #define R_MAC_CHUP0_BASE 0x00000320 #define R_MAC_ENABLE 0x00000400 #define R_MAC_STATUS 0x00000408 #define R_MAC_INT_MASK 0x00000410 #define R_MAC_TXD_CTL 0x00000420 #define R_MAC_MDIO 0x00000428 #if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480) #define R_MAC_STATUS1 0x00000430 #endif /* 1250 PASS2 || 112x PASS1 || 1480 */ #define R_MAC_DEBUG_STATUS 0x00000448 #define MAC_HASH_COUNT 8 #define MAC_ADDR_COUNT 8 #define MAC_CHMAP_COUNT 4 /* ********************************************************************* * DUART Registers ********************************************************************* */ #if SIBYTE_HDR_FEATURE_1250_112x /* This MC only on 1250 & 112x */ #define R_DUART_NUM_PORTS 2 #define A_DUART 0x0010060000 #define DUART_CHANREG_SPACING 0x100 #define A_DUART_CHANREG(chan, reg) \ (A_DUART + DUART_CHANREG_SPACING * ((chan) + 1) + (reg)) #endif /* 1250 & 112x */ #define R_DUART_MODE_REG_1 0x000 #define R_DUART_MODE_REG_2 0x010 #define R_DUART_STATUS 0x020 #define R_DUART_CLK_SEL 0x030 #define R_DUART_CMD 0x050 #define R_DUART_RX_HOLD 0x060 #define R_DUART_TX_HOLD 0x070 #if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480) #define R_DUART_FULL_CTL 0x040 #define R_DUART_OPCR_X 0x080 #define R_DUART_AUXCTL_X 0x090 #endif /* 1250 PASS2 || 112x PASS1 || 1480 */ /* * The IMR and ISR can't be addressed with A_DUART_CHANREG, * so use these macros instead. */ #if SIBYTE_HDR_FEATURE_1250_112x /* This MC only on 1250 & 112x */ #define DUART_IMRISR_SPACING 0x20 #define DUART_INCHNG_SPACING 0x10 #define A_DUART_CTRLREG(reg) \ (A_DUART + DUART_CHANREG_SPACING * 3 + (reg)) #define R_DUART_IMRREG(chan) \ (R_DUART_IMR_A + (chan) * DUART_IMRISR_SPACING) #define R_DUART_ISRREG(chan) \ (R_DUART_ISR_A + (chan) * DUART_IMRISR_SPACING) #define R_DUART_INCHREG(chan) \ (R_DUART_IN_CHNG_A + (chan) * DUART_INCHNG_SPACING) #define A_DUART_IMRREG(chan) A_DUART_CTRLREG(R_DUART_IMRREG(chan)) #define A_DUART_ISRREG(chan) A_DUART_CTRLREG(R_DUART_ISRREG(chan)) #define A_DUART_INCHREG(chan) A_DUART_CTRLREG(R_DUART_INCHREG(chan)) #endif /* 1250 & 112x */ #define R_DUART_AUX_CTRL 0x010 #define R_DUART_ISR_A 0x020 #define R_DUART_IMR_A 0x030 #define R_DUART_ISR_B 0x040 #define R_DUART_IMR_B 0x050 #define R_DUART_OUT_PORT 0x060 #define R_DUART_OPCR 0x070 #define R_DUART_IN_PORT 0x080 #define R_DUART_SET_OPR 0x0B0 #define R_DUART_CLEAR_OPR 0x0C0 #define R_DUART_IN_CHNG_A 0x0D0 #define R_DUART_IN_CHNG_B 0x0E0 /* * These constants are the absolute addresses. */ #define A_DUART_MODE_REG_1_A 0x0010060100 #define A_DUART_MODE_REG_2_A 0x0010060110 #define A_DUART_STATUS_A 0x0010060120 #define A_DUART_CLK_SEL_A 0x0010060130 #define A_DUART_CMD_A 0x0010060150 #define A_DUART_RX_HOLD_A 0x0010060160 #define A_DUART_TX_HOLD_A 0x0010060170 #define A_DUART_MODE_REG_1_B 0x0010060200 #define A_DUART_MODE_REG_2_B 0x0010060210 #define A_DUART_STATUS_B 0x0010060220 #define A_DUART_CLK_SEL_B 0x0010060230 #define A_DUART_CMD_B 0x0010060250 #define A_DUART_RX_HOLD_B 0x0010060260 #define A_DUART_TX_HOLD_B 0x0010060270 #define A_DUART_INPORT_CHNG 0x0010060300 #define A_DUART_AUX_CTRL 0x0010060310 #define A_DUART_ISR_A 0x0010060320 #define A_DUART_IMR_A 0x0010060330 #define A_DUART_ISR_B 0x0010060340 #define A_DUART_IMR_B 0x0010060350 #define A_DUART_OUT_PORT 0x0010060360 #define A_DUART_OPCR 0x0010060370 #define A_DUART_IN_PORT 0x0010060380 #define A_DUART_ISR 0x0010060390 #define A_DUART_IMR 0x00100603A0 #define A_DUART_SET_OPR 0x00100603B0 #define A_DUART_CLEAR_OPR 0x00100603C0 #define A_DUART_INPORT_CHNG_A 0x00100603D0 #define A_DUART_INPORT_CHNG_B 0x00100603E0 #if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1) #define A_DUART_FULL_CTL_A 0x0010060140 #define A_DUART_FULL_CTL_B 0x0010060240 #define A_DUART_OPCR_A 0x0010060180 #define A_DUART_OPCR_B 0x0010060280 #define A_DUART_INPORT_CHNG_DEBUG 0x00100603F0 #endif /* 1250 PASS2 || 112x PASS1 */ /* ********************************************************************* * Synchronous Serial Registers ********************************************************************* */ #if SIBYTE_HDR_FEATURE_1250_112x /* sync serial only on 1250/112x */ #define A_SER_BASE_0 0x0010060400 #define A_SER_BASE_1 0x0010060800 #define SER_SPACING 0x400 #define SER_DMA_TXRX_SPACING 0x80 #define SER_NUM_PORTS 2 #define A_SER_CHANNEL_BASE(sernum) \ (A_SER_BASE_0 + \ SER_SPACING*(sernum)) #define A_SER_REGISTER(sernum,reg) \ (A_SER_BASE_0 + \ SER_SPACING*(sernum) + (reg)) #define R_SER_DMA_CHANNELS 0 /* Relative to A_SER_BASE_x */ #define A_SER_DMA_CHANNEL_BASE(sernum,txrx) \ ((A_SER_CHANNEL_BASE(sernum)) + \ R_SER_DMA_CHANNELS + \ (SER_DMA_TXRX_SPACING*(txrx))) #define A_SER_DMA_REGISTER(sernum, txrx, reg) \ (A_SER_DMA_CHANNEL_BASE(sernum, txrx) + \ (reg)) /* * DMA channel registers, relative to A_SER_DMA_CHANNEL_BASE */ #define R_SER_DMA_CONFIG0 0x00000000 #define R_SER_DMA_CONFIG1 0x00000008 #define R_SER_DMA_DSCR_BASE 0x00000010 #define R_SER_DMA_DSCR_CNT 0x00000018 #define R_SER_DMA_CUR_DSCRA 0x00000020 #define R_SER_DMA_CUR_DSCRB 0x00000028 #define R_SER_DMA_CUR_DSCRADDR 0x00000030 #define R_SER_DMA_CONFIG0_RX 0x00000000 #define R_SER_DMA_CONFIG1_RX 0x00000008 #define R_SER_DMA_DSCR_BASE_RX 0x00000010 #define R_SER_DMA_DSCR_COUNT_RX 0x00000018 #define R_SER_DMA_CUR_DSCR_A_RX 0x00000020 #define R_SER_DMA_CUR_DSCR_B_RX 0x00000028 #define R_SER_DMA_CUR_DSCR_ADDR_RX 0x00000030 #define R_SER_DMA_CONFIG0_TX 0x00000080 #define R_SER_DMA_CONFIG1_TX 0x00000088 #define R_SER_DMA_DSCR_BASE_TX 0x00000090 #define R_SER_DMA_DSCR_COUNT_TX 0x00000098 #define R_SER_DMA_CUR_DSCR_A_TX 0x000000A0 #define R_SER_DMA_CUR_DSCR_B_TX 0x000000A8 #define R_SER_DMA_CUR_DSCR_ADDR_TX 0x000000B0 #define R_SER_MODE 0x00000100 #define R_SER_MINFRM_SZ 0x00000108 #define R_SER_MAXFRM_SZ 0x00000110 #define R_SER_ADDR 0x00000118 #define R_SER_USR0_ADDR 0x00000120 #define R_SER_USR1_ADDR 0x00000128 #define R_SER_USR2_ADDR 0x00000130 #define R_SER_USR3_ADDR 0x00000138 #define R_SER_CMD 0x00000140 #define R_SER_TX_RD_THRSH 0x00000160 #define R_SER_TX_WR_THRSH 0x00000168 #define R_SER_RX_RD_THRSH 0x00000170 #define R_SER_LINE_MODE 0x00000178 #define R_SER_DMA_ENABLE 0x00000180 #define R_SER_INT_MASK 0x00000190 #define R_SER_STATUS 0x00000188 #define R_SER_STATUS_DEBUG 0x000001A8 #define R_SER_RX_TABLE_BASE 0x00000200 #define SER_RX_TABLE_COUNT 16 #define R_SER_TX_TABLE_BASE 0x00000300 #define SER_TX_TABLE_COUNT 16 /* RMON Counters */ #define R_SER_RMON_TX_BYTE_LO 0x000001C0 #define R_SER_RMON_TX_BYTE_HI 0x000001C8 #define R_SER_RMON_RX_BYTE_LO 0x000001D0 #define R_SER_RMON_RX_BYTE_HI 0x000001D8 #define R_SER_RMON_TX_UNDERRUN 0x000001E0 #define R_SER_RMON_RX_OVERFLOW 0x000001E8 #define R_SER_RMON_RX_ERRORS 0x000001F0 #define R_SER_RMON_RX_BADADDR 0x000001F8 #endif /* 1250/112x */ /* ********************************************************************* * Generic Bus Registers ********************************************************************* */ #define IO_EXT_CFG_COUNT 8 #define A_IO_EXT_BASE 0x0010061000 #define A_IO_EXT_REG(r) (A_IO_EXT_BASE + (r)) #define A_IO_EXT_CFG_BASE 0x0010061000 #define A_IO_EXT_MULT_SIZE_BASE 0x0010061100 #define A_IO_EXT_START_ADDR_BASE 0x0010061200 #define A_IO_EXT_TIME_CFG0_BASE 0x0010061600 #define A_IO_EXT_TIME_CFG1_BASE 0x0010061700 #define IO_EXT_REGISTER_SPACING 8 #define A_IO_EXT_CS_BASE(cs) (A_IO_EXT_CFG_BASE+IO_EXT_REGISTER_SPACING*(cs)) #define R_IO_EXT_REG(reg, cs) ((cs)*IO_EXT_REGISTER_SPACING + (reg)) #define R_IO_EXT_CFG 0x0000 #define R_IO_EXT_MULT_SIZE 0x0100 #define R_IO_EXT_START_ADDR 0x0200 #define R_IO_EXT_TIME_CFG0 0x0600 #define R_IO_EXT_TIME_CFG1 0x0700 #define A_IO_INTERRUPT_STATUS 0x0010061A00 #define A_IO_INTERRUPT_DATA0 0x0010061A10 #define A_IO_INTERRUPT_DATA1 0x0010061A18 #define A_IO_INTERRUPT_DATA2 0x0010061A20 #define A_IO_INTERRUPT_DATA3 0x0010061A28 #define A_IO_INTERRUPT_ADDR0 0x0010061A30 #define A_IO_INTERRUPT_ADDR1 0x0010061A40 #define A_IO_INTERRUPT_PARITY 0x0010061A50 #define A_IO_PCMCIA_CFG 0x0010061A60 #define A_IO_PCMCIA_STATUS 0x0010061A70 #define A_IO_DRIVE_0 0x0010061300 #define A_IO_DRIVE_1 0x0010061308 #define A_IO_DRIVE_2 0x0010061310 #define A_IO_DRIVE_3 0x0010061318 #define A_IO_DRIVE_BASE A_IO_DRIVE_0 #define IO_DRIVE_REGISTER_SPACING 8 #define R_IO_DRIVE(x) ((x)*IO_DRIVE_REGISTER_SPACING) #define A_IO_DRIVE(x) (A_IO_DRIVE_BASE + R_IO_DRIVE(x)) #define R_IO_INTERRUPT_STATUS 0x0A00 #define R_IO_INTERRUPT_DATA0 0x0A10 #define R_IO_INTERRUPT_DATA1 0x0A18 #define R_IO_INTERRUPT_DATA2 0x0A20 #define R_IO_INTERRUPT_DATA3 0x0A28 #define R_IO_INTERRUPT_ADDR0 0x0A30 #define R_IO_INTERRUPT_ADDR1 0x0A40 #define R_IO_INTERRUPT_PARITY 0x0A50 #define R_IO_PCMCIA_CFG 0x0A60 #define R_IO_PCMCIA_STATUS 0x0A70 /* ********************************************************************* * GPIO Registers ********************************************************************* */ #define A_GPIO_CLR_EDGE 0x0010061A80 #define A_GPIO_INT_TYPE 0x0010061A88 #define A_GPIO_INPUT_INVERT 0x0010061A90 #define A_GPIO_GLITCH 0x0010061A98 #define A_GPIO_READ 0x0010061AA0 #define A_GPIO_DIRECTION 0x0010061AA8 #define A_GPIO_PIN_CLR 0x0010061AB0 #define A_GPIO_PIN_SET 0x0010061AB8 #define A_GPIO_BASE 0x0010061A80 #define R_GPIO_CLR_EDGE 0x00 #define R_GPIO_INT_TYPE 0x08 #define R_GPIO_INPUT_INVERT 0x10 #define R_GPIO_GLITCH 0x18 #define R_GPIO_READ 0x20 #define R_GPIO_DIRECTION 0x28 #define R_GPIO_PIN_CLR 0x30 #define R_GPIO_PIN_SET 0x38 /* ********************************************************************* * SMBus Registers ********************************************************************* */ #define A_SMB_XTRA_0 0x0010060000 #define A_SMB_XTRA_1 0x0010060008 #define A_SMB_FREQ_0 0x0010060010 #define A_SMB_FREQ_1 0x0010060018 #define A_SMB_STATUS_0 0x0010060020 #define A_SMB_STATUS_1 0x0010060028 #define A_SMB_CMD_0 0x0010060030 #define A_SMB_CMD_1 0x0010060038 #define A_SMB_START_0 0x0010060040 #define A_SMB_START_1 0x0010060048 #define A_SMB_DATA_0 0x0010060050 #define A_SMB_DATA_1 0x0010060058 #define A_SMB_CONTROL_0 0x0010060060 #define A_SMB_CONTROL_1 0x0010060068 #define A_SMB_PEC_0 0x0010060070 #define A_SMB_PEC_1 0x0010060078 #define A_SMB_0 0x0010060000 #define A_SMB_1 0x0010060008 #define SMB_REGISTER_SPACING 0x8 #define A_SMB_BASE(idx) (A_SMB_0+(idx)*SMB_REGISTER_SPACING) #define A_SMB_REGISTER(idx, reg) (A_SMB_BASE(idx)+(reg)) #define R_SMB_XTRA 0x0000000000 #define R_SMB_FREQ 0x0000000010 #define R_SMB_STATUS 0x0000000020 #define R_SMB_CMD 0x0000000030 #define R_SMB_START 0x0000000040 #define R_SMB_DATA 0x0000000050 #define R_SMB_CONTROL 0x0000000060 #define R_SMB_PEC 0x0000000070 /* ********************************************************************* * Timer Registers ********************************************************************* */ /* * Watchdog timers */ #define A_SCD_WDOG_0 0x0010020050 #define A_SCD_WDOG_1 0x0010020150 #define SCD_WDOG_SPACING 0x100 #define SCD_NUM_WDOGS 2 #define A_SCD_WDOG_BASE(w) (A_SCD_WDOG_0+SCD_WDOG_SPACING*(w)) #define A_SCD_WDOG_REGISTER(w, r) (A_SCD_WDOG_BASE(w) + (r)) #define R_SCD_WDOG_INIT 0x0000000000 #define R_SCD_WDOG_CNT 0x0000000008 #define R_SCD_WDOG_CFG 0x0000000010 #define A_SCD_WDOG_INIT_0 0x0010020050 #define A_SCD_WDOG_CNT_0 0x0010020058 #define A_SCD_WDOG_CFG_0 0x0010020060 #define A_SCD_WDOG_INIT_1 0x0010020150 #define A_SCD_WDOG_CNT_1 0x0010020158 #define A_SCD_WDOG_CFG_1 0x0010020160 /* * Generic timers */ #define A_SCD_TIMER_0 0x0010020070 #define A_SCD_TIMER_1 0x0010020078 #define A_SCD_TIMER_2 0x0010020170 #define A_SCD_TIMER_3 0x0010020178 #define SCD_NUM_TIMERS 4 #define A_SCD_TIMER_BASE(w) (A_SCD_TIMER_0+0x08*((w)&1)+0x100*(((w)&2)>>1)) #define A_SCD_TIMER_REGISTER(w, r) (A_SCD_TIMER_BASE(w) + (r)) #define R_SCD_TIMER_INIT 0x0000000000 #define R_SCD_TIMER_CNT 0x0000000010 #define R_SCD_TIMER_CFG 0x0000000020 #define A_SCD_TIMER_INIT_0 0x0010020070 #define A_SCD_TIMER_CNT_0 0x0010020080 #define A_SCD_TIMER_CFG_0 0x0010020090 #define A_SCD_TIMER_INIT_1 0x0010020078 #define A_SCD_TIMER_CNT_1 0x0010020088 #define A_SCD_TIMER_CFG_1 0x0010020098 #define A_SCD_TIMER_INIT_2 0x0010020170 #define A_SCD_TIMER_CNT_2 0x0010020180 #define A_SCD_TIMER_CFG_2 0x0010020190 #define A_SCD_TIMER_INIT_3 0x0010020178 #define A_SCD_TIMER_CNT_3 0x0010020188 #define A_SCD_TIMER_CFG_3 0x0010020198 #if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1) #define A_SCD_SCRATCH 0x0010020C10 #endif /* 1250 PASS2 || 112x PASS1 */ #if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480) #define A_SCD_ZBBUS_CYCLE_COUNT 0x0010030000 #define A_SCD_ZBBUS_CYCLE_CP0 0x0010020C00 #define A_SCD_ZBBUS_CYCLE_CP1 0x0010020C08 #endif /* ********************************************************************* * System Control Registers ********************************************************************* */ #define A_SCD_SYSTEM_REVISION 0x0010020000 #define A_SCD_SYSTEM_CFG 0x0010020008 #define A_SCD_SYSTEM_MANUF 0x0010038000 /* ********************************************************************* * System Address Trap Registers ********************************************************************* */ #define A_ADDR_TRAP_INDEX 0x00100200B0 #define A_ADDR_TRAP_REG 0x00100200B8 #define A_ADDR_TRAP_UP_0 0x0010020400 #define A_ADDR_TRAP_UP_1 0x0010020408 #define A_ADDR_TRAP_UP_2 0x0010020410 #define A_ADDR_TRAP_UP_3 0x0010020418 #define A_ADDR_TRAP_DOWN_0 0x0010020420 #define A_ADDR_TRAP_DOWN_1 0x0010020428 #define A_ADDR_TRAP_DOWN_2 0x0010020430 #define A_ADDR_TRAP_DOWN_3 0x0010020438 #define A_ADDR_TRAP_CFG_0 0x0010020440 #define A_ADDR_TRAP_CFG_1 0x0010020448 #define A_ADDR_TRAP_CFG_2 0x0010020450 #define A_ADDR_TRAP_CFG_3 0x0010020458 #if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480) #define A_ADDR_TRAP_REG_DEBUG 0x0010020460 #endif /* 1250 PASS2 || 112x PASS1 || 1480 */ #define ADDR_TRAP_SPACING 8 #define NUM_ADDR_TRAP 4 #define A_ADDR_TRAP_UP(n) (A_ADDR_TRAP_UP_0 + ((n) * ADDR_TRAP_SPACING)) #define A_ADDR_TRAP_DOWN(n) (A_ADDR_TRAP_DOWN_0 + ((n) * ADDR_TRAP_SPACING)) #define A_ADDR_TRAP_CFG(n) (A_ADDR_TRAP_CFG_0 + ((n) * ADDR_TRAP_SPACING)) /* ********************************************************************* * System Interrupt Mapper Registers ********************************************************************* */ #define A_IMR_CPU0_BASE 0x0010020000 #define A_IMR_CPU1_BASE 0x0010022000 #define IMR_REGISTER_SPACING 0x2000 #define IMR_REGISTER_SPACING_SHIFT 13 #define A_IMR_MAPPER(cpu) (A_IMR_CPU0_BASE+(cpu)*IMR_REGISTER_SPACING) #define A_IMR_REGISTER(cpu, reg) (A_IMR_MAPPER(cpu)+(reg)) #define R_IMR_INTERRUPT_DIAG 0x0010 #define R_IMR_INTERRUPT_LDT 0x0018 #define R_IMR_INTERRUPT_MASK 0x0028 #define R_IMR_INTERRUPT_TRACE 0x0038 #define R_IMR_INTERRUPT_SOURCE_STATUS 0x0040 #define R_IMR_LDT_INTERRUPT_SET 0x0048 #define R_IMR_LDT_INTERRUPT 0x0018 #define R_IMR_LDT_INTERRUPT_CLR 0x0020 #define R_IMR_MAILBOX_CPU 0x00c0 #define R_IMR_ALIAS_MAILBOX_CPU 0x1000 #define R_IMR_MAILBOX_SET_CPU 0x00C8 #define R_IMR_ALIAS_MAILBOX_SET_CPU 0x1008 #define R_IMR_MAILBOX_CLR_CPU 0x00D0 #define R_IMR_INTERRUPT_STATUS_BASE 0x0100 #define R_IMR_INTERRUPT_STATUS_COUNT 7 #define R_IMR_INTERRUPT_MAP_BASE 0x0200 #define R_IMR_INTERRUPT_MAP_COUNT 64 /* * these macros work together to build the address of a mailbox * register, e.g., A_MAILBOX_REGISTER(R_IMR_MAILBOX_SET_CPU,1) * for mbox_0_set_cpu2 returns 0x00100240C8 */ #define A_MAILBOX_REGISTER(reg,cpu) \ (A_IMR_CPU0_BASE + (cpu * IMR_REGISTER_SPACING) + reg) /* ********************************************************************* * System Performance Counter Registers ********************************************************************* */ #define A_SCD_PERF_CNT_CFG 0x00100204C0 #define A_SCD_PERF_CNT_0 0x00100204D0 #define A_SCD_PERF_CNT_1 0x00100204D8 #define A_SCD_PERF_CNT_2 0x00100204E0 #define A_SCD_PERF_CNT_3 0x00100204E8 #define SCD_NUM_PERF_CNT 4 #define SCD_PERF_CNT_SPACING 8 #define A_SCD_PERF_CNT(n) (A_SCD_PERF_CNT_0+(n*SCD_PERF_CNT_SPACING)) /* ********************************************************************* * System Bus Watcher Registers ********************************************************************* */ #define A_SCD_BUS_ERR_STATUS 0x0010020880 #if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1) #define A_SCD_BUS_ERR_STATUS_DEBUG 0x00100208D0 #define A_BUS_ERR_STATUS_DEBUG 0x00100208D0 #endif /* 1250 PASS2 || 112x PASS1 */ #define A_BUS_ERR_DATA_0 0x00100208A0 #define A_BUS_ERR_DATA_1 0x00100208A8 #define A_BUS_ERR_DATA_2 0x00100208B0 #define A_BUS_ERR_DATA_3 0x00100208B8 #define A_BUS_L2_ERRORS 0x00100208C0 #define A_BUS_MEM_IO_ERRORS 0x00100208C8 /* ********************************************************************* * System Debug Controller Registers ********************************************************************* */ #define A_SCD_JTAG_BASE 0x0010000000 /* ********************************************************************* * System Trace Buffer Registers ********************************************************************* */ #define A_SCD_TRACE_CFG 0x0010020A00 #define A_SCD_TRACE_READ 0x0010020A08 #define A_SCD_TRACE_EVENT_0 0x0010020A20 #define A_SCD_TRACE_EVENT_1 0x0010020A28 #define A_SCD_TRACE_EVENT_2 0x0010020A30 #define A_SCD_TRACE_EVENT_3 0x0010020A38 #define A_SCD_TRACE_SEQUENCE_0 0x0010020A40 #define A_SCD_TRACE_SEQUENCE_1 0x0010020A48 #define A_SCD_TRACE_SEQUENCE_2 0x0010020A50 #define A_SCD_TRACE_SEQUENCE_3 0x0010020A58 #define A_SCD_TRACE_EVENT_4 0x0010020A60 #define A_SCD_TRACE_EVENT_5 0x0010020A68 #define A_SCD_TRACE_EVENT_6 0x0010020A70 #define A_SCD_TRACE_EVENT_7 0x0010020A78 #define A_SCD_TRACE_SEQUENCE_4 0x0010020A80 #define A_SCD_TRACE_SEQUENCE_5 0x0010020A88 #define A_SCD_TRACE_SEQUENCE_6 0x0010020A90 #define A_SCD_TRACE_SEQUENCE_7 0x0010020A98 #define TRACE_REGISTER_SPACING 8 #define TRACE_NUM_REGISTERS 8 #define A_SCD_TRACE_EVENT(n) (((n) & 4) ? \ (A_SCD_TRACE_EVENT_4 + (((n) & 3) * TRACE_REGISTER_SPACING)) : \ (A_SCD_TRACE_EVENT_0 + ((n) * TRACE_REGISTER_SPACING))) #define A_SCD_TRACE_SEQUENCE(n) (((n) & 4) ? \ (A_SCD_TRACE_SEQUENCE_4 + (((n) & 3) * TRACE_REGISTER_SPACING)) : \ (A_SCD_TRACE_SEQUENCE_0 + ((n) * TRACE_REGISTER_SPACING))) /* ********************************************************************* * System Generic DMA Registers ********************************************************************* */ #define A_DM_0 0x0010020B00 #define A_DM_1 0x0010020B20 #define A_DM_2 0x0010020B40 #define A_DM_3 0x0010020B60 #define DM_REGISTER_SPACING 0x20 #define DM_NUM_CHANNELS 4 #define A_DM_BASE(idx) (A_DM_0 + ((idx) * DM_REGISTER_SPACING)) #define A_DM_REGISTER(idx, reg) (A_DM_BASE(idx) + (reg)) #define R_DM_DSCR_BASE 0x0000000000 #define R_DM_DSCR_COUNT 0x0000000008 #define R_DM_CUR_DSCR_ADDR 0x0000000010 #define R_DM_DSCR_BASE_DEBUG 0x0000000018 #if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1) #define A_DM_PARTIAL_0 0x0010020ba0 #define A_DM_PARTIAL_1 0x0010020ba8 #define A_DM_PARTIAL_2 0x0010020bb0 #define A_DM_PARTIAL_3 0x0010020bb8 #define DM_PARTIAL_REGISTER_SPACING 0x8 #define A_DM_PARTIAL(idx) (A_DM_PARTIAL_0 + ((idx) * DM_PARTIAL_REGISTER_SPACING)) #endif /* 1250 PASS3 || 112x PASS1 */ #if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1) #define A_DM_CRC_0 0x0010020b80 #define A_DM_CRC_1 0x0010020b90 #define DM_CRC_REGISTER_SPACING 0x10 #define DM_CRC_NUM_CHANNELS 2 #define A_DM_CRC_BASE(idx) (A_DM_CRC_0 + ((idx) * DM_CRC_REGISTER_SPACING)) #define A_DM_CRC_REGISTER(idx, reg) (A_DM_CRC_BASE(idx) + (reg)) #define R_CRC_DEF_0 0x00 #define R_CTCP_DEF_0 0x08 #endif /* 1250 PASS3 || 112x PASS1 */ /* ********************************************************************* * Physical Address Map ********************************************************************* */ #if SIBYTE_HDR_FEATURE_1250_112x #define A_PHYS_MEMORY_0 _SB_MAKE64(0x0000000000) #define A_PHYS_MEMORY_SIZE _SB_MAKE64((256*1024*1024)) #define A_PHYS_SYSTEM_CTL _SB_MAKE64(0x0010000000) #define A_PHYS_IO_SYSTEM _SB_MAKE64(0x0010060000) #define A_PHYS_GENBUS _SB_MAKE64(0x0010090000) #define A_PHYS_GENBUS_END _SB_MAKE64(0x0040000000) #define A_PHYS_LDTPCI_IO_MATCH_BYTES_32 _SB_MAKE64(0x0040000000) #define A_PHYS_LDTPCI_IO_MATCH_BITS_32 _SB_MAKE64(0x0060000000) #define A_PHYS_MEMORY_1 _SB_MAKE64(0x0080000000) #define A_PHYS_MEMORY_2 _SB_MAKE64(0x0090000000) #define A_PHYS_MEMORY_3 _SB_MAKE64(0x00C0000000) #define A_PHYS_L2_CACHE_TEST _SB_MAKE64(0x00D0000000) #define A_PHYS_LDT_SPECIAL_MATCH_BYTES _SB_MAKE64(0x00D8000000) #define A_PHYS_LDTPCI_IO_MATCH_BYTES _SB_MAKE64(0x00DC000000) #define A_PHYS_LDTPCI_CFG_MATCH_BYTES _SB_MAKE64(0x00DE000000) #define A_PHYS_LDT_SPECIAL_MATCH_BITS _SB_MAKE64(0x00F8000000) #define A_PHYS_LDTPCI_IO_MATCH_BITS _SB_MAKE64(0x00FC000000) #define A_PHYS_LDTPCI_CFG_MATCH_BITS _SB_MAKE64(0x00FE000000) #define A_PHYS_MEMORY_EXP _SB_MAKE64(0x0100000000) #define A_PHYS_MEMORY_EXP_SIZE _SB_MAKE64((508*1024*1024*1024)) #define A_PHYS_LDT_EXP _SB_MAKE64(0x8000000000) #define A_PHYS_PCI_FULLACCESS_BYTES _SB_MAKE64(0xF000000000) #define A_PHYS_PCI_FULLACCESS_BITS _SB_MAKE64(0xF100000000) #define A_PHYS_RESERVED _SB_MAKE64(0xF200000000) #define A_PHYS_RESERVED_SPECIAL_LDT _SB_MAKE64(0xFD00000000) #define A_PHYS_L2CACHE_WAY_SIZE _SB_MAKE64(0x0000020000) #define PHYS_L2CACHE_NUM_WAYS 4 #define A_PHYS_L2CACHE_TOTAL_SIZE _SB_MAKE64(0x0000080000) #define A_PHYS_L2CACHE_WAY0 _SB_MAKE64(0x00D0180000) #define A_PHYS_L2CACHE_WAY1 _SB_MAKE64(0x00D01A0000) #define A_PHYS_L2CACHE_WAY2 _SB_MAKE64(0x00D01C0000) #define A_PHYS_L2CACHE_WAY3 _SB_MAKE64(0x00D01E0000) #endif #endif
© 2026 UnknownSec