Openwrt repeater same subnet. So it's also written on the mentioned page: Sep 4, 2022 · Imagine if you were sitting between two people with the same name and you had an envelope marked with that name that you were supposed to hand to one of them (but not the other) how would you know who to give it to if they have the same name. Oct 28, 2019 · Is it possible to use OpenWrt on a wireless extender and keep the device on the same subnet as the main network? I have a Netgear EX3700 and I was running OpenWrt on it for about a month but I couldn't figure out how to set it up so that the interfaces on both networks were using the same subnet. Configuring WDS will make the network unusable. 4 GHz) from that AP, and retransmit under that same SSID of 'MySID' via 2. 10 (repeater) if you got a . I've added the client and acces point networks but the Internet doesen't work. Due to technical limitations, your OpenWrt device will create its own subnet (in the example below it's Jul 21, 2020 · Hi all - first post here. x/24 using the 2. 0/24 network accept requests originating outside their own IP subnet? Temporarily enable masquerading on the guest zone to check if this is the case. The router can access the internet (websites ping succesfully) but any device connected to the router (Ethernet or Wireless) can't ping the internet. Using dd-wrt now but thinking about moving to openwrt if it can solve the issues I have with wirelessly connecting two subnets. 168. 5, but I would like to have the LAN 192. I couldn't find a clear Aug 31, 2024 · Hello friends, I need to make my OpenWrt router as the wifi repeater with different subnet. x/24), to have a dedicated network with internet access. 1) with CC 15. 5. 10 Therefore it should not be possible to access . I had to set it up like this: WiFi network: 192. Is there a way that I can run a different wifi netwrok (192. what happens main router (192. Oct 1, 2022 · The repeater itself (under the hood) works with . (the WAN interface is set to DHCP client), but the configuration will fail upon save and revert. 0/24, I have followed and read diverging comments but I can't get to a solution, I hope someone has the patience to help me . 0. There is now a wireless link with two non-gateway routers linking the two networks Aug 28, 2020 · Hi everyone, I have an OpenWRT dual-band router and I'd like to share the internet wirelessly in a separate subnet using it. Main Page - DD-WRT Wiki The wireless AP 's address should be on the same subnet as your main router, but outside the DHCP range used when assigning addresses to connected devices. 254 and the other is 192. Now the wwan is 192. 05. While OpenWrt does support these standards, setting them up needs a bit more technical know-how, and is not completely straightforward for users unfamiliar with roaming. Two wireless protocols can be used to achieve this: WDS and 802. I bought additional router (TP-Link MR3020) and flash it with CC 15. So in GLI UI you can just configure WDS repeater. Jul 27, 2019 · Hi everyone, I installed openwrt on a router to use it as a repeater for the main router but I would also like to have the same subnet as the main router. 30 and the LAN 192. 2. 2 and 192. 11s mesh. Jun 18, 2025 · In the default configuration, OpenWrt bridges the wireless network to the LAN of the device. Most wireless drivers do not support bridging in client mode, therefore the traffic between LAN and the wireless client must be routed. Assuming that the DHCP server is running on an upstream OpenWrt device, this means that by default the wireless AP router IP should be between 192. . Situation: Two adjacent apartments, each apartment having an internet gateway on a different subnet (one is 192. 0/24; excluded from the DHCP on said server. 60. 10 dhcp ip. It will receive its data via a WiFi link (2. Hi! I have a TP-LINK TL-WR940N and I'm trying to make a Wi-Fi repeater. Thanks. Please advice on how to set it up correctly so everything will stay on the same network. right now I have made it relayed based repeater but I cannot have different SSID. I want to connect to the primary AP that is in 192. 1 and I want this MR3020 to be WiFi extender because I got very poor signal in my bathroom. 1) on my repeater with different SSID while disable client wifi Hope Sep 21, 2016 · If you use repeater mode and want your subnet is the same as your main router, the right configuration is WDS. I want to use additional router as WiFi repeater in the same subnet Hello friends, I have main router (192. Unfortunately your main router doesn’t support WDS. 10 to pass all data to . Thank you. Same IP range, so that users can almost seamlessly move from one area to the other. Setting up APs to the same SSID/password (and, important thing, same type of encryption! Jun 13, 2025 · Devices connected to both the access point and the repeater will share the same subnet, enabling visibility between them and facilitating the use of protocols like Zeroconf. 1. 5 days ago · Do the devices on the 192. That can only with PC static connected to repeater in the right subnet. 254). What is the subnet of your upstream router (A)? What are you setting for your downstream (B)? Oct 14, 2022 · Connect to client Wi-Fi network Connect to client Wi-Fi network This page will explain how to connect your OpenWrt device to another Wi-Fi network by using its own radio. 0/24 Extender network: 192. 4 and 5 GHz. 4Ghz interface and share the internet on the 5Ghz interface in a different subnet with a different SSID (192. 0/24 I From what I understand I should disable the DHCP server on the repeater and set the repeater ip as one in the ip range of the main router, but when doing so I don't have access to the repeater anymore and I need to reset to factory default. Both the access point and the repeater remain accessible over the network. 1) SSID get extended through the repeater as well. 99. 2, or even try setting the LAN interface to "DHCP client". This document focuses In this video, you'll learn exactly how to set up your OpenWRT router as a reliable Wi-Fi Range Extender (Repeater Mode) to eliminate wireless dead zones and boost signal strength across your home Mar 4, 2024 · In the 2nd router's OpenWRT settings, I tried assigning the 2nd router's LAN interface IP to 192. Also, I can't seem to use the same subnet for both LAN and WWAN networks, since the router will Mar 25, 2023 · The OpenWRT repeater (EnGenius EAP600) will sit on a fixed IP in 192. cltksdnb ciehor zjjyjg qmvp lgop bth dfhb ydfny egs edols